Document overview
Digital Workshop Manual documentation for model LAMBORGHINI SPARK 230 VRT → WSXFN30200LL10001 from the SPARK VRT (STAGE 5) family. Language: English; 2,164 pages.
The corresponding English table of contents contains 51 sections and 762 individual topics.
Main sections included
- Introduction
- Safety
- Technical characteristics
- Calibrations and electronic diagnosis
- Method of intervention
- Wiring diagrams
- Service Info
Document details
- Brand: LAMBORGHINI
- Family: SPARK VRT (STAGE 5)
- Model: SPARK 230 VRT
- Starting serial number: WSXFN30200LL10001
- Document type: Workshop Manual
- Language: English
- Pages: 2,164
- File size: 589.57 MiB
- Format: Digital PDF download
Compatibility
Before purchasing, verify that your machine model and reference code match LAMBORGHINI SPARK 230 VRT → WSXFN30200LL10001.
Complete table of contents
Introduction
- Tightening torques
- Wheel nut/screw tightening torques
- Tightening torques for nuts and bolts of electrical connections
- Installation of solenoid valves and cartridge valves
- Installation of quick couplers
- One-way valves
- Fixing the steering wheel
- Spool valves
- Units of measurement and conversion factors
Safety
Preface
- Important notes concerning safety
Important safety information
- Recognising hazards
- Indications for persons in contact with the tractor
Safety rules
- Risks during tractor preparation
- Risks during maintenance
- Work on machine systems
- Special disassembly/assembly/inspection procedures
Safety pictograms
- Replacing safety pictograms
Environmental risks
- Hazards associated with the operating environment
Technical characteristics
- External views
- Viste interni cabina
- Dimensions and weights of the tractor
- Main technical data
Engine
- Pressure transducer (exhaust gas backpressure) – (B60)
- Pressure transducer (ahead of SCR catalytic converter) – (B88)
- Differential pressure transducer (diesel particulate filter) – (B61)
- Differential pressure transducer (diesel particulate filter) – (B58)
- Pressure sensor (Rail) – (B49)
- Pressure transducer (lubricant oil) – (B6) / (fuel) – (B51)
- Pressure transducer (ahead of SCR catalytic converter) – (B88)
- Pressure transducer
- Pressure transducer
- Pressure/temperature sender (engine intake air) – (B48)
- Pressure/temperature sender (engine intake air) – (B48)
- Temperature sender (exhaust gas recirculation) – (B64)
- Temperature sender (intake air, ambient air) – (B74)
- Temperature sender (ahead of and after diesel oxidation catalyst) – (B65)
- Temperature sender (ahead of and after diesel oxidation catalyst) – (B65)
- Temperature sender (ahead of SCR catalytic converter) – (B78)
- Temperature sender (ahead of SCR catalytic converter) – (B78)
- Speed sensor (crankshaft) – (B40.2)
- Speed sensor (camshaft) – (B40.1) / (crankshaft) – (B40.2)
- Speed sensor (camshaft) – (B40.1)
- NOx sensor (SCR ahead of catalytic converter) – (B54)
- NOx sensor (SCR ahead of catalytic converter) – (B54)
- NOx sensor (SCR ahead of catalytic converter) – (B54)
- NOx sensor (SCR after catalytic converter) – (B56)
Engine accessories
- Expansion tank
- Coolant radiator
- Air filter
- Intercooler
- Diesel radiator
- Diesel fuel tank
- Diesel pre-filter
- AdBlue tank
- AdBlue float
Transmission
- Modular architecture transmission
- Modular architecture transmission
Rear axle
- Rear axle
- Rear brakes
- Air braking
- Rear PTO
- Checking and topping up the oil level of the rear final drive units
Front axle
- General characteristics
Bodywork – Cab – Platform
- Air conditioning system
- Instrument cluster
- Right-hand console
- Front console and cab pillars
- Multifunction armrest
- Roof panel
- Left hand console
- Openable roof hatch
- Ballasts – Technical data
- Ballasts
- Drawbar
Hydraulic system
- Base hydraulic circuit
- Full house hydraulic circuit
- Optional hydraulic circuit
- Optional hydraulic circuit 1
- Optional hydraulic circuit 2
- Optional hydraulic circuit 3
- Transmission hydraulic circuit 1
- Transmission hydraulic circuit 2
- Base hydraulic circuit
- Full house hydraulic circuit
- Optional hydraulic circuit
- Optional hydraulic circuit 1
- Optional hydraulic circuit 2
- Transmission hydraulic circuit 1
- Transmission hydraulic circuit 2
- Hydraulic pumps
- Auxiliary utility oil tank
- 22,5 cc variable displacement pump
- RH variable displacement pump, 22.5 + 40 cc
- Variable displacement pump 22.5 + 40 cc + 11 cc
- 45 cc variable displacement pump
- 63 cc variable displacement pump
- Oil delivery filter 50 bar
- Orbitrol 70/270
- Orbitrol 70/230 LSRM
Front PTO
- Front PTO
Front lift
- Front lift
Rear lift
- Rear lift
Calibrations and electronic diagnosis
- ECUs
Diagnostic tools
- D-Tech and diagnostic ports
- D-TECH App
- ECUs
Commissioning and calibrating the tractor
- Commissioning procedure (EOL)
- ECU Reset
- Set vehicle model
- Transmission Control Unit (TCU) initialization
- ECUs initialization
- Distributors configuration
- Maximum vehicle speed
- Tyre type
- Language
- Measurement unit
- Front Power Take-Off (PTO)
- Radar
- Automatic Air Conditioning
- iMonitor
- ISO 11786
- Iso 11783
- MMI (man machine interface)
- Agrosky
- Font Susp.
- ASM (Automatic Steering Management)
- Front speed sensor
- Oil pump displacement
- Stoll
- Engine brake
- Front Wet brake
- Pneumatic trailer brake
- Pneumatic trailer brake MR
- Rear PTO
- Radio CAN
- PTO front ratio configuration
- GTECU init
- Distributors command calibration neutral
- eTCV parameters configuration
- Clutch pedal calibration
- Throttle pedal calibration
- Hand gas calibration
- Park brake parameter configuration
- Slope sensor calibration
- Water mix motor calibration
- Recirculation Motor calibration
- Draft sensor calibration
- Rear hitch position calibration
- Steering angle calibration
- Front hitch calibration
- Front suspension calibration
- Wheel angle sensor calibration
- PVED-CL Valve spool calibration
ECU alarms
- SDF Severity of alarms
- ECU ALARMS
Software management
- Engine dataset upgrade
Method of intervention
B0 – Engine
- V-belt pulley
- Disassembly and refitting of the belt tensioner (ribbed V-belt, level 1)
- Disassembly and refitting of the belt tensioner (ribbed V-belt, level 1)
- Removal and assembly of the fan support
- Removal and assembly of the fan support
- Disassembly and assembly of fan mount
- Removal and assembly of the fan support
- Fastener elements (fan mount)
- Removing and fitting the belt tensioner (ribbed V-belt, level 2)
- Checking crankcase pressure
- Removing and fitting the crankcase breather
- Disassembling and assembling crankcase breather
- Removing and fitting the crankcase breather
- Removing and fitting the crankcase breather
- Removing and fitting the crankcase breather
- Removing and fitting the crankcase breather
- Blanking tools (crankcase, electronic engine governor)
- Blanking elements
- Fastener elements (crankcase)
- Blanking tool (crankcase)
- Mount (crankcase breather)
- Pipe (crankcase breather)
- Support (Assembly foot, opposite side to flywheel)
- Fitting and removing the rotation device
- Fitting and removing the rotation device (PTOC power take off)
- Blanking elements (crankcase, PTO-A)
- Blanking elements (crankcase, PTO-A)
- Fastener elements (gearbox, PTOC power take off)
- Fastener elements (gearbox, PTOC power take off)
- Fastener elements (PTO-B power take off)
- Blanking elements (PTO-B)
- Blanking elements (PTO-B)
- Disassembling and assembling the connector housing
- Cover (connector casing)
- Cover (connector casing)
- Cover (connector casing)
- Replacing crankshaft seal ring (side opposite flywheel).
- Fitting and removing the crankshaft sleeve (side opposite flywheel)
- Disassembling and assembling the front cover (fixing elements)
- Checking the camshaft bearing
- Removing and fitting and the crankshaft bearing cap
- Removing and fitting the V belt pulley/poly-V belt pulley
- Removing and fitting the torsional vibration damper
- Disassembling and assembling the torsional vibration damper
- Removing and fitting the torsional vibration damper
- Disassembling and assembling the flywheel (fixing elements)
- Replacing the starter motor ring gear of the flywheel
- Fitting and removing the crankshaft bearings
- Checking the crankshaft
- Check the endfloat of the crankshaft
- Fitting and removing the crankshaft bearings
- Checking the crankshaft bearings
- Removing and fitting the sensor wheel
- Replacing the crankshaft seal ring (flywheel side)
- Removing and fitting the connecting rod shank
- Checking the connecting rod shank
- Disassembling and assembling the piston
- Disassembling and assembling the piston rings
- Check the piston rings
- Check the piston rings
- Check the piston rings
- Measuring piston protrusion
- Checking compression
- Removing and fitting the cylinder head cover
- Removing and fitting the cylinder head cover
- Disassembling and assembling the cylinder head (fasteners)
- Removing and fitting the valves
- Checking valves, valve guides, valve springs and valve recess
- Blanking elements (cylinder head)
- Transport eye-bolt (cylinder head)
- Transport eye-bolt (cylinder head)
- Transport eye-bolt (cylinder head)
- Checking and setting valve clearance (6 cylinder)
- Assembly and disassembly of the distribution valve
- Removing and refitting the valve timing system
- Disassembly and assembly of the control elements
- Oil dipstick
- Oil dipstick
- Removing and fitting the lubricant oil sump (pressed steel lubricant oil sump)
- Disassembling and assembling the lubricant oil sump (pressed steel sump)
- Removing and fitting lubricant oil sump (heavy version)
- Removing and fitting lubricant oil sump (heavy version)
- Removing and fitting lubricant oil sump (heavy version)
- Oil filler neck
- Removing and fitting lubricant oil cooler
- Removing and fitting lubricant oil cooler (fastener elements)
- Removing and fitting the lubricant oil cooler
- Removing and fitting lubricant oil cooler
- Removing and fitting the lubricant oil cooler housing
- Removing and fitting the lubricant oil cooler housing (fastener elements)
- Blanking elements (lubricant oil cooler housing)
- Fastener elements (lubricant oil cooler housing)
- Fastener elements (lubricant oil cooler housing)
- Coolant pipe (lubricant oil radiator housing – crankcase)
- Coolant pipe (lubricant oil cooler – cylinder head)
- Removing and fitting the oil suction pipe
- Replacing the injector bush
- Cleaning the injector bush
- Cleaning the injector bush seat
- Disassembly and assembly of the fuel control unit (fastening elements)
- Disassembling and completing assembly of the fuel control unit (2000 bar injection system)
- Disassembly and completion of the fuel control unit
- Disassembling and assembling the high pressure pump (fastener elements)
- Removing and fitting the injector (1600 bar injection system)
- Removing and fitting the injector (1600 bar injection system)
- Removing and fitting the injector (2000 bar injection system)
- Removing and fitting the fuel filter console (bowl)
- Removing and fitting the fuel pump (fastener elements)
- Flexible hose connectors
- Fuel filter
- Fuel filter
- Fuel filter
- Fuel filter
- Connector plug (fuel delivery pump)
- Removing and fitting the fuel lines (fuel pump – pilot block)
- Removing and fitting the fuel line (pilot block high pressure pumps)
- Disassembling and assembling the rail (1600 bar injection system)
- Removing and fitting the rail (1600 bar injection system)
- Removing and fitting the rail (1600 bar injection system)
- Fitting and removing the pressure limiting valve (Rail)
- Fitting and removing the pressure limiting valve (Rail)
- Fitting and removing the rail pressure sensor
- Removing and refitting fuel lines (Rail, cylinder head, fuel control unit – fuel filter)
- Fuel pipe (fuel filter – pilot block)
- Fuel pipe (rail, cylinder head, pilot block)
- Fuel pipe (fuel delivery pump, fuel filter, pilot block)
- Fuel pipes (Rail, cylinder head, pilot lock- fuel filter)
- Vibration damper (assembly position)
- Pressure transducer (exhaust gas backpressure)
- Pressure transducer (exhaust gas backpressure)
- Assembly and disassembly of piston cooling nozzles
- Assembly and disassembly of piston cooling nozzles
- Removing and fitting the coolant pump
- Removing and fitting the coolant pump (V-belt, level 1)
- Removing and fitting the coolant pump (fastening elements)
- Removing and fitting the coolant pump
- Removing and fitting the coolant pump
- Removing and refitting adapter (coolant pump – thermostat housing)
- Transmission components (coolant pump)
- Removing and fitting the thermostat
- Disassembling and assembling the thermostat
- Removing and fitting the thermostat
- Check the thermostat (after removing)
- Check the thermostat (after removing)
- Removing and fitting the thermostat housing (fastener elements)
- Removal and installation of the thermostat housing
- Removal and installation of the thermostat housing
- Removal and installation of the thermostat housing
- Fastener elements (coolant pump thermostat housing)
- Fastener elements (thermostat housing)
- Blanking elements (thermostat housing)
- Blanking elements (thermostat housing)
- Fastener elements (thermostat housing)
- Fastener elements (thermostat housing)
- Flexible hose fastening (Thermostat housing)
- Flexible hose connector (thermostat box)
- Fitting (compensation line)
- Breather pipe (thermostat box – cooler)
- Pipes (EGR radiator cylinder head)
- Pipes (EGR radiator cylinder head)
- Compensation line (thermostat box)
- Connector cable (intake air)
- Removing and refitting the diesel particulate filter
- Removing and fitting the turbocharger
- Removing and fitting the turbocharger
- Removing and fitting the turbocharger
- Disassembling and assembling the lubricating oil pipe (exhaust gas turbocharger)
- Disassembling and assembling the lubricating oil pipe (exhaust gas turbocharger)
- Removing and fitting the lubricant oil return pipe (upper section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (upper section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (upper section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (lower section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (lower section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (lower section) (Turbocharger)
- Cover guard (Differential pressure transducer)
- Disassembling and assembling the heater
- Disassembling and assembling the heater
- Disassembling and assembling the heater
- Removing and fitting the charge air elbow pipe
- Disassembling and assembling the mixer pipe
- Disassembling and assembling the mixer pipe
- Disassembling and assembling the butterfly valve
- Disassembling and assembling the butterfly valve
- Disassembly and assembly of the flange
- Removing and refitting the diesel particulate filter
- Mixer pipe (threaded connection) SCR (Selective Catalytic Reduction)
- Mixer pipe (fastening element) SCR (Selective Catalytic Reduction)
- Disassembling and assembling alternator (poly-V-belt, level 1)
- Disassembling and assembling the console (ribbed V-belt, level 1)
- Disassembling and assembling the console (ribbed V-belt, level 1)
- Disassembling and assembling the crankshaft speed sensor (fasteners)
- SCR delivery pump (Selective Catalytic Reduction)
C0 – Engine accessories
- Removing and fitting the fan mount (fastener elements)
- Mount (assembly foot, side opposite of the flywheel)
- Mount (assembly foot, flywheel side)
- Manual fuel pump
- Assembly of the pressure transducer (fuel pressure)
- Check the seal of the cooling system
- Intake manifold (exhaust gas turbocharger)
- Disassembly and refitting of the intake air pressure/temperature sender
- Fastener elements (wiring bundle)
- Fastener elements (wiring bundle)
- Mount (fasteners)
- Support plate (on the charge air pipe)
- Mounting plate (on boost air hose)
- Cable harness (fastener elements)
- Protective cap (relay)
- Heater (connector line)
- Flushing the SCR (Selective Catalytic Reduction) delivery pump
- Flushing/Checking SCR (Selective Catalytic Reduction) metering unit
- Flushing the SCR (Selective Catalytic Reduction) pipe (delivery pump – metering unit)
- Fitting (starter motor)
- Fitting (starter motor)
- Shield plate (starter motor)
- Shield plate (starter)
- Starter (fasteners)
- Removing and refitting the diesel particulate filter (module size 9.5″)
- Fastener elements (exhaust aftertreatment system) (NOx sensor, temperature sender, diesel particulate filter differential pressure sender)
- Mount (module size 9.5”)
- V-Band clamp.
- VBand clamp (3″ exhaust pipe)
- VBand clamp (4″ exhaust pipe)
- Inlet module (module size 9.5″)
- Outlet module (module size 9.5″)
- Mixer pipe (threaded connection)
- Alternator
- Alternator
- Removing and fitting the rotational speed sensor (crankshaft)
- Disassembling and assembling the crankshaft speed sensor (fasteners)
- Disassembling and assembling the camshaft speed sensor (ancillaries)
- Disassembly and refitting of the intake air pressure/temperature sender
- Temperature sender (coolant)
- Fitting the pressure transducer (fuel pressure / lubricant oil pressure)
- Heater relay
- Relay (heater, thermo-starter, glow plugs)
- Disassembling and assembling the NOx sensor
- Disassembling and assembling the pressure transducer (exhaust back-pressure)
- Assembling the SCR (Selective Catalytic Reduction) metering unit
- Differential pressure sender (diesel particulate filter)
- Differential pressure sender (diesel particulate filter)
- Temperature sender (upstream of the SCR catalytic converter)
- Temperature sender (ahead of and after diesel oxidation catalytic converter)
- Temperature sender (exhaust gas)
- Temperature sender (inlet air and ambient air temperature)
- SCR (Selective Catalytic Reduction) solenoid valve
- Connector cable (relay – alternator)
- Connector cable (relay – heater)
- Replacing the engine coolant
- Bleeding the fuel circuit
- Engine air fan
- Water radiator
- Removing the water radiator
- Complete cooling pack
- Diesel radiator
- Transmission oil radiator
- Intercooler and gearbox oil / fuel heat exchanger
- Engine air filter
- Engine air intake pipe
- Diesel fuel tank
- Diesel pre-filter
- AdBlue tank
- AdBlue pump
D0 – Transmission
- Changing the transmission oil
- General repair instructions
- Tightening Torques
- Adjusting unit
- Control unit
- Control block
- Sensors on the gearbox housing
- Wiring loom
- Valve blocks (clutch control)
- Piping
- Hydraulic module
- Removing and installing the gearbox
- Gearbox
- Pump drive gear carrier
- Transmission oil level
- Assembling 4WD manifold
- Fitting 4WD clutch
- PTO ring nut / PTO shafts
- Fitting PTO control rods
- Tightening the gearbox flange screws
- Tightening screws of PTO flange and top link
- Fitting and testing the PTO clutch
- Installing PTO cartridge seal
- Disassembling pinion bearings and matching bearings correctly for assembly
- Tightening screws of bevel ring gear
- Adjusting the bevel gear set
- Adjusting conical bearings of 4WD transfer shaft
- Adjusting conical bearings of 4WD shaft
- Rear pinion casing
- Adjusting the bevel gear set and the pump drive bearings
- Flexible coupling
- Disassembling the rear PTO
- 4WD transfer shaft
- 4WD shaft
- 4WD clutch unit
- Disassembling the 4WD clutch
- Rear PTO casing
- Rear PTO clutch
- Transmission Control Unit (GCU)
- Transmission oil filter
E0 – Rear axle
- Bleeding the braking system
- Draining the rear axle and filling with oil
- Applying sealant
- Rear differential
- Removing rear differential
- Driveline Assembly
- Tightening brake adapter screws
- Adjusting brake dead zone
- Adjusting the wheel carrier bearings
- Fitting wheel carrier cartridge seal
- Fitting brake cover seal
- EPB adjustment procedure
- Left hand rear axle
- Left hand rear ring gear
- LH brake carrier
- Left hand brake actuator
- Left hand brake discs
F0 – Front axle
- 4WD shaft
- Carrier with front axle
- Front axle
- Safety precautions
- Oil Draining Mandatory Procedure
- Pivot brackets
- Planetary reduction gearbox and steering knuckle housing
- Stub axle and steering sensor
- Steering cylinders
- Differential assembly
- Conical pinion
G0 – Bodywork – Cab – Platform
- Empty and charge the air conditioning system
- Cab
- Cab access steps
- Front cab carrier brackets
- Engine hood and front hood panels
- Lower hood guard
- Battery mount
- Front mudguards
- Mat
- Right hand console
- Left hand console
- Instrument panel
- Instrument cluster
- Right hand pillar cover
- Left hand rear pillar cover
- Seat
- Passenger seat
- Steering wheel
- Headliner trim
- Air conditioning condenser
- Dehydrator filter
- A/C unit
- Master cylinder
H0 – Hydraulic system
- Draining and filling the auxiliary utility oil
- Installing the pump dive connector sleeves
- Main oil suction line filter
- Acoustic filter
- Oil delivery line filter
- Priority valve
- Front axle suspension solenoid valve block
- Left hand hydraulic pump (22,5 + 40 + 11) cc
- Right hand hydraulic pump, 22,5 cc
- Variable displacement hydraulic pump, 85 cc
- Hydrostatic steering (orbitrol)
- Auxiliary utility oil tank
- Front lift distributors
- Disassembling the auxiliary utility distributors
- Air tanks
- Pneumatic braking system air filter
- Left hand air reservoir
- Installation of solenoid valves
L0 – Electrical system
- Battery
- Auxiliary battery
- Engine Control Unit (ECU)
- Electronic control unit (PFCU)
- Instrument panel
M0 – Front PTO
- Front PTO
- Front PTO shaft
N0 – Front lift
- Front lift arm carrier
- Front lift cylinders
- Front top link
R0 – Rear lift
- Aligning lift carriers
- Fitting lift position sensor
- Rear lift
- Rear lift hydraulic cylinders
- Rear lift arms
- Rear three-point linkage with hydraulic tie-rod
- Rear top link carrier
S0 – Wheels
- Front Wheels
- Rear wheel
V0 – Ballast – towing hitches
- Rear towing hitch
Wiring diagrams
Components
- Locations of main ECUs
- AdBlue supply module
- ISO 11786 Control unit
- Engine Control Unit (ECU)
- CTM (ECU)
- Gear Box Control Unit
- HLHP Control unit
- Service Controller Body
- TECU Service control unit
- Trailer air braking control unit – Mother regulation
- A – Starting and charging
- B – Fuses
- C – Grounds
- D – Intermediate connections
- E – On-board instruments
- F – External lights (rotating beacon)
- G – Interior lights
- H – Manual electrical controls (steering column stalk)
- I – Circuit breakers
- J – Relays
- K – Sensors and transmitters
- L – Electromagnets and solenoid valves
- M – Electrical/electronic devices, Flasher units and Timers
- N – Electric motors and actuators
- O – Resistors and rheostats
- P – Various services
- R – Diagnostics
Systems
- S001 – Power
- S002 – Starter
- S003 – Engine cooling
- S004 – Engine control system
- S005 – Emissions control system
- S006 – Front lights
- S007 – Rear work lights
- S008 – Roof lights
- S009 – Front work lights
- S010 – Sidelights and turn indicators
- S011 – Internal illumination
- S012 – Defrost and wiper
- S013 – Horn
- S014 – Mirror adjustment
- S015 – Radio
- S016 – Power socket – accessories
- S017 – Air conditioning
- S018 – Front lift
- S019 – Rear lift
- S020 – Rear mudguards
- S021 – Braking system
- S022 – Trailer brake
- S023 – Transmission
- S024 – Isobus line
- S025 – CAN “AUX” line
- S026 – “VEHICLE” CAN line
- S027 – CAN BODY line
- S028 – Agrosky
- S029 – i-Monitor
- S030 – Front axle
- S031 – Front loader
- S032 – Prewiring for solenoid valve module
- S033 – Distributors
Wiring harnesses
- 0.012.4030.4 – Front PTO
- 0.014.1567.4/30 – Front wiper motor – opening windscreen version
- 0.016.8489.4 – Trailer solenoid valve
- 0.017.0496.4/10A – H9 left hand lower front work lights
- 0.017.0496.4/10B – H9 right hand lower front work lights
- 0.017.0497.4/30A – H9 left hand bottom rear lights
- 0.017.0497.4/30B – H9 right hand bottom rear lights
- 0.017.8425.4/10 – Trailer socket, EU
- 0.017.8426.4_10 – Trailer socket (USA)
- 0.019.2379.4/20A – Front lights on left hand arm (EU)
- 0.019.2379.4/20B – Front lights on right hand arm (EU)
- 0.019.2380.4/50 – Hazard warning lights switch (USA)
- 0.019.2571.4/10 – ISO 11786
- 0.019.3659.4/30 – i-Monitor (Base version)
- 0.019.4559.4/10 – H9 rear work light (service)
- 0.019.4689.4/30A – H9 left hand rear work lights on roof
- 0.019.4689.4_30B – H9 right hand rear work lights on roof
- 0.019.4914.4_30A – LED left hand rear work lights on roof
- 0.019.4914.4_30B – LED right hand rear work lights on roof
- 0.019.5311.4/10 – Automatic A/C system
- 0.019.9829.4/30 – Agrosky SR10 antenna
- 0.020.1009.4A – Front lights on left hand arm (USA)
- 0.020.1009.4B – Front lights on right hand arm (USA)
- 0.020.8862.4/30 – Roof
- 0.020.9559.4 – Front/rear camera (10 m)
- 0.021.0490.4/10 – Trailer ABS
- 0.021.1028.4/10 – AS (Agrosky) Adapter
- 0.021.3696.4_50A – Left hand rear mudguards
- 0.021.3696.4_50B – Right hand rear mudguards
- 0.021.3866.4/30 – Front ISOBUS 11783 socket
- 0.021.5509.4 – Rear screen defrost adapter
- 0.021.2367.4/50 – Fuse box (PCB in cab)
- 0.021.8276.4 – Camera (3 m)
- 0.021.8291.4A – LED bottom front work lights
- 0.021.8291.4B – LED right hand bottom front work lights
- 0.021.8334.4A – LED left hand bottom rear lights
- 0.021.8334.4B – LED right hand bottom rear lights
- 0.023.9008.4/20 – Cowl
- 0.023.9202.4/10 – Front axle steering sensor (Dana)
- 0.023.9204.4/10 – Electrohydraulic steering (Agrosky)
- 0.023.9207.4/10 – Cable adapter on front arm
- 0.023.9248.4 – Viscostatic fan
- 0.023.9250.4_20A – Left hand rear mudguards
- 0.023.9250.4_20B – Right hand rear mudguards
- 0.023.9582.4/40 – LED front work lights on cab roof
- 0.023.9583.4/40 – H9 front work lights on cab roof
- 0.025.5687.4/10 – i-Monitor
- 0.025.5688.4 – USB video camera module
- 0.025.9765.4 – Adapter cable for i-Monitor (X25)
- 0.026.3703.4 – AdBlue quality sensor
- 0.026.6351.4 – Two-speed front power take off (PTO)
- 0.027.1782.4 – Camera 1 (3,2 m)
- 0.027.1783.4 – Camera 2 (5 m)
- 0.027.5538.4 – License plate light
- 0.027.6393.4/10 – Hydraulic trailer braking (MR)
- 0.031.4657.4A – Left turn indicator adapter cable
- 0.031.4657.4B – Left hand turn indicator adapter cable
- 0.032.8553.4 – Provision for ISO 11783 socket
- 0.033.0899.4 – AGI2 antenna cable
- 0.033.7162.4/10 – Main battery fuse box (Basic PCB version)
- 0.033.7163.4/50 – Centre wiring loom 2
- 0.033.7165.4/20 – Distributors
- 0.033.7166.4/40 – Centre wiring loom 1
- 0.033.7167.4/40 – Gearbox
- 0.033.7171.4/40 – Engine – 250 HP version
- 0.033.7172.4 – Battery power cables
- 0.033.7175.4/30 – Basic battery cables
- 0.033.7176.4 – Ethernet wiring loom
- 0.033.7177.4/10 – ABS – STOLL – EV
- 0.033.7178.4/10 – AGROSKY SR20 ELECTRIC CABLE
- 0.033.7180.4/20 – Rear ISOBUS 11783 socket
- 0.033.7181.4 – Front lift
- 0.033.7184.4 – Trailer air braking
- 0.033.7185.4/10 – Cab
- 0.033.7186.4 – Console
- 0.033.7187.4 – Works lights on roof and rear view mirrors – LED version
- 0.033.7188.4 – Auxiliary distributors
- 0.033.7189.4 – Works lights on roof and rear view mirrors – H9 version
- 0.033.7190.4/20 – Main battery fuse box (Full PCB version)
- 0.033.7191.4A – LED left hand work lights 5-6
- 0.033.7191.4B – LED right hand work lights 5-6
- 0.033.7192.4 – Hydraulic trailer braking (NO MR)
- 0.033.7259.4A – Left hand bi-LED headlights
- 0.033.7259.4B – Right hand bi-LED headlights
- 0.033.8944.4_20A – Adapter for LED left hand front TOP lights
- 0.033.8944.4_20B – Adapter for LED right hand front TOP lights
- 0.033.9905.4 – FM and DAB antenna
- 0.034.0493.4/20 – Battery – Cab adapter
- 0.034.2047.4 – FM and DAB antenna amplifier
- 0.034.2048.4 – FM antenna cable
- 0.034.2049.4 – DAB antenna cable
- 0.036.2448.4A – LED front lights on left hand arm (EU)
- 0.036.2448.4B – LED front lights on right hand arm (EU)
- 0.036.2449.4A – LED front lights on left hand arm (USA)
- 0.036.2449.4B – LED front lights on right hand arm (USA)
- 0.036.7926.4A – LED left hand turn indicator adapter cable
- 0.036.7926.4B – LED right hand turn indicator adapter cable
- 0.036.8039.4/10 – Full version battery cables + provision for front loader
- 0.036.8040.4/10 – Full version battery cables + provision for solenoid valve module
- 0.037.0255.4 – UFI filter heater interface
- 0.039.9737.4 – LED light on rear mudguard
- 0.040.1839.4 – MR_CUNA hydraulic trailer braking
- 04422324.4/10 – ISO 11786 socket
- 04436707_10A – Left hand rotating beacon
- 04436707_10B – Right hand rotating beacon
Service Info
A0 – TRACTOR
- Diagnostics 2026 subscription
- SERVICE NEWS – TTV SERIES – CRUISE CONTROL BEHAVIOUR
- After-sales 2026 subscription
- SERVICE NEWS RESEARCH GUIDE
- Diagnostics 2025 subscription
- After-sales 2025 subscription
- Diagnostics 2023 subscription
- Diagnostics 2024 subscription
- After-sales 2024 subscription
- After-sales 2023 subscription
C0 – ENGINE ACCESSORIES
- SERVICE NEWS – DEF Unit – Wrong level indication
- Possible Dust entry at air duct sleeve
- Diagnostic protocol – AdBlue – Float level unit
- Filter and prefilter tool p/n 5.9035.865.0
- SCR AREA DAMAGED SENSORS
D0 – TRANSMISSION
- SERVICE NEWS – EQ transmission – Increased noise level at specific working point
- SERVICE NEWS – EQ transmission – adjustment unit improvements
- SERVICE NEWS – T7340/7540/7560/7780 – Malfunction of HD pressure sensor
- Error 521035 – Leakage at HD pipes
- Introduction of new long filter variant at T7340/ T7540/ T7560/ T7780
- Transmission SW Update (Agrotron 6190TTV-6210TTV-6230TTV-6230HDTTV-7250TTV-7250HDTTV-8280TTV Stage 5)
F0 – FRONT AXLE
- Bevel gear set loosing screws
G0 – BODYWORK – CAB
- Brake booster pump internal damage
- Scheduled maintenance intervals
H0 – HYDRAULIC AND PNEUMATIC SYSTEM|
- SERVICE NEWS – Brake bleeding diagnostic procedure
- SERVICE NEWS – HPT – Front axle suspension – Damaged 2.8l accumulator
- Hydraulic CUNA trailer braking kit (ITALY)
- Single connection hydraulic braking kit availability update – only for EUROPEAN market
- Dry front brake discs – damaged brake pipes
- Damaged O-ring at front axle brakes charging valve block
- Oil tank-New refilling procedure
L0 – ELECTRIC AL SYSTEM
- SERVICE NEWS – New fixation for LED driving lights
- SERVICE NEWS – Software package release 2026-02
- PRESSURE SWITCH ON TRAILER BRAKE VALVE “CUNA”
- Air pressure sensor malfunction
- SerDia4.0
- iMonitor x35 malfunctioning
- GO-ANYWHERE DIAGNOSTICS
- iMonitor SW upgrade & iMonitor UBOOT update instruction
- Series 6/7/8 TTV – new software package January 2023
- Lost connection diagnostic tools
- Series 6/7/8 TTV – water in connector at external fuse box
- Water entrance in connector
- New Electrical cable P/N 0.037.0255.4/10
- PTO switch not working
- Precision Farming and iMonitor user manuals
R0 – REAR LIFT
- Twisted lifting shaft
V1 – AFTERMARKET KITS
- Check correct installation of braking KIT
- Instructions for kit aftersales
- Rear inner fenders with additional dirt protection
