Document overview
Workshop Manual for DEUTZ FAHR TCD 2012 L06 2V DCR Stage 3A from the Tractor components – Engine – DEUTZ AG Stage 3 family. Digital PDF in English with 300 pages.
The corresponding English table of contents contains 9 sections and 79 individual topics.
Main sections included
- Introduction
- Technical characteristics
- Calibrations and electronic diagnosis
- Method of intervention
Document details
- Brand: DEUTZ FAHR
- Family: Tractor components – Engine – DEUTZ AG Stage 3
- Model: TCD 2012 L06 2V DCR Stage 3A
- Document type: Workshop Manual
- Language: English
- Pages: 300
- File size: 26.09 MiB
- Format: Digital PDF download
Compatibility
Before purchasing, verify that your machine model and reference code match DEUTZ FAHR TCD 2012 L06 2V DCR Stage 3A.
Complete table of contents
Introduction
- Introduction – Engines
Technical characteristics
Engine
- Components of the TCD 2012 L04/L06 2V DCR engine
- Test and adjustment data (L3)
- Tightening requirements TCD 2012 L04/L06 2V DCR engine
Calibrations and electronic diagnosis
Diagnostic tools
Serdia 2000
- SERDIA 2000 level III” software
Method of intervention
- Tools for engine disassembly and reassembly
- Workshop tools for engine disassembly and reassembly
- Tightening Torques
B0 – Engine
- Air conditioning compressor drive belt
- Tension adjustment of the fan and air conditioning compressor drive belt
- Alternator, fuel pump and water pump drive belt
- Tension adjustment of the alternator, fuel pump and water pump drive belt
- Check the compression value (L3)
- Assembly and disassembly of the engine on the assembly stand (L3)
- Valve clearance adjustment (with the exhaust gas recirculation module absent or removed) (L3)
- Valve clearance adjustment (with the exhaust gas recirculation module installed) (L3)
- Disassembly and assembly of the rocker and support (L3)
- Disassemble and complete the rocker and support, check
- Disassembly and assembly of the cylinder head (L3)
- Valve assembly and disassembly (L3)
- Valve check (L3)
- Check the valve guide (L3)
- Check the valve residual (L3)
- Crankshaft check (L3)
- Replace the crankshaft O-ring (flywheel end) (L3)
- Replace the crankshaft O-ring (opposite end to flywheel) (L3)
- Connecting rod drum check (L3)
- Assembly and disassembly of the crankshaft (L3)
- Disassembly and assembly of the piston and connecting rod drum (L3)
- Check the piston (L3)
- Check the piston rings and piston grooves (L3)
- Assembly and disassembly of the piston cooling nozzles (L3)
- Removing and fitting crankcase breather (L3)
- Checking cylinder (L3)
- Removal and refitting of the front cover (opposite end to flywheel) (L3)
- Disassembly and assembly of the connector box (L3)
- Disassembly and assembly of the gear case cover (L3)
- Assembly and disassembly of the camshaft (L3)
- Check the camshaft (L3)
- Disassembly and assembly of the turbocharger (L3)
- Disassembly and assembly of the turbocharging air duct (L3)
- Fitting and removing the exhaust gas recovery module (L3)
- Removing and fitting the fuel delivery pump (driven by ribbed V-belt) (L3)
- Removing and fitting the fuel control unit (L3)
- Removing and fitting high pressure pump (installation position A) (L3)
- Removing and fitting high pressure pump (installation position B) (L3)
- Removing and fitting the common rail system (L3)
- Removing and fitting injector (L3)
- Removing and fitting the pressure cut-off valve (L3)
- Removing and fitting the fuel pressure transducer (L3)
- Assembly and disassembly of the oil intake pipe (L3)
- Disassembly and assembly of the lubricant oil sump (L3)
- Disassembly and assembly of the oil radiator (L3)
- Removing and fitting the lubricant oil cooler housing (L3)
- Removing and fitting the lubricant oil filter (L3)
- Removing and fitting the oil pressure switch (L3)
- Removing and fitting reservoir (L3)
- Removing and fitting the coolant pump (driven by ribbed V-belt) (L3)
- Removing and refitting fan motor (L3)
- Removing and fitting fan motor (L3)
- Removing and fitting fan mount (L3)
- Disassembly and assembly of the torsional vibration damper (L3)
- Removing and fitting belt tensioner (ribbed V-belt) (L3)
- Assembly and disassembly of the flywheel (L3)
C0 – Engine accessories
- Starter motor
- Fitting and removing thermostat (L3)
- Testing the thermostat (after removal)
- Removal and refitting of the crankshaft speed sensor (L3)
- Removal and refitting of the camshaft speed sensor (L3)
- Removing and refitting the exhaust manifold (L3)
- Fitting and removing the solenoid valve (exhaust gas recovery module) (L3)
- Removing and fitting the fuel filter mount (L3)
- Assembly and disassembly of the temperature sender (L3)
- Removal and refitting of the supply air pressure/temperature sender (L3)
- Removing and fitting the alternator (driven by ribbed V-belt) (L3)
- Fitting and removing the rail pressure sensor (L3)
- Disassembly and assembly of the cable bundle (L3)
- Disassembly and assembly of the starter (L3)
- Fitting and removing the glow plugs (L3)
