Document overview

Digital Workshop Manual documentation for model DEUTZ FAHR 6175 AGROTRON TTV → WSXCF00200LD10000 from the Series 6 Agrotron TTV (STAGE 3A – STAGE 4) family. Language: English; 2,531 pages.

The corresponding English table of contents contains 50 sections and 828 individual topics.

Main sections included

Introduction
Safety
Technical characteristics
Calibrations and electronic diagnosis
Method of intervention
Wiring diagrams
Service Info

Document details

Brand: DEUTZ FAHR
Family: Series 6 Agrotron TTV (STAGE 3A – STAGE 4)
Model: 6175 AGROTRON TTV
Starting serial number: WSXCF00200LD10000
Document type: Workshop Manual
Language: English
Pages: 2,531
File size: 632.37 MiB
Format: Digital PDF download

Compatibility

Before purchasing, verify that your machine model and reference code match DEUTZ FAHR 6175 AGROTRON TTV → WSXCF00200LD10000.

Complete table of contents

Introduction
- Tightening torques
- Installation of solenoid valves and cartridge valves
- Pump tightening torques
- Installation of quick couplers
- Units of measurement and conversion factors
Safety
- Preface
  - Important notes concerning safety
- Important safety information
  - Recognising hazards
  - Indications for persons in contact with the tractor
- Safety rules
  - Risks during tractor preparation
  - Risks during maintenance
  - Work on machine systems
  - Special disassembly/assembly/inspection procedures
- Safety pictograms
  - Replacing safety pictograms
- Environmental risks
  - Hazards associated with the operating environment
Technical characteristics
- Engine
  - Technical data – Pressure/temperature transmitter
  - Technical data – Pressure transducer
  - Pressure transducer
  - Technical data – Pressure transducer
  - Pressure sensor
  - Technical data – Pressure transducer
  - Pressure transducer
  - Technical data – Pressure sensor
  - Technical data – Temperature transmitter
  - Technical data – Temperature transmitter
  - Technical data – Temperature transmitter
  - Temperature sender
  - Technical data – Temperature transmitter
  - Technical data – Temperature transmitter
  - Technical data – Speed indicator
  - Technical data – Speed indicator
  - Technical data – Speed indicator
  - technical specifications – NOx sensor (24 V)
  - technical specifications – NOx sensor (12 V)
- Transmission
  - Transmission
  - Rear PTO
- Rear axle
  - Rear axle
- Front axle
  - Front axle
  - General characteristics
- Bodywork – Cab – Platform
  - Brake master cylinders
  - Air conditioning system
  - Air conditioning system
  - Air conditioning system – Diagnostics
  - General introduction to the A/C system
  - Compressor
  - Condenser
  - Filter-dryer
  - Expansion valve
- Hydraulic system
  - Hydraulic System
  - TRANSMISSION circuit, base version (“Mother Regulation”)
  - TRANSMISSION circuit, optional version (“Mother Regulation”)
  - TRANSMISSION circuit, optional version 2 (“Mother Regulation”)
  - Agrosky circuit
  - Ancillary utility distributor – 8-way version
  - Ancillary utility distributor – 10-way version
  - Variable displacement pump
  - Variable displacement pump (63cc/rev)
  - Gear pump for steering system (19 cc/rev)
  - Gear pump for steering system (22.5 cc/rev)
  - Priority valve
  - Front suspension system – INTEGRAL accumulators
  - Hydraulic power steering (OSPD)
  - LS hydraulic power steering (OSPEDC)
  - Hydraulic front axle suspension
  - Servo-brake valve for front axle
  - Servo-brake valve for front axle – Version with front brakes
  - Braking system
  - Master cylinder
  - Rear lift distributor
  - Ancillary utility distributor – Version for front lift
  - Hydraulic trailer braking system – Italy version
  - Hydraulic trailer braking system – Export version
  - Hydraulic pump
  - Load sensing valve, pressure cut-off valve
  - Bistable valve block
  - Suction line filter
  - Delivery line filter
  - Oil return filter
  - Oil filter
  - Pump filter
  - LS variable displacement pump filter
  - Logic block – brakes
  - Compressor
  - Pressure limiting valve
  - Trailer air braking valve (2-way)
  - Trailer air braking valve (1-way)
  - Trailer air brake boost solenoid valve
  - Trailer parking brake control solenoid valve
  - Quick pressure release valve
- Front PTO
  - Front PTO
Calibrations and electronic diagnosis
- ECUs
- Diagnostic tools
  - D-Tech and diagnostic ports
  - D-TECH App
  - SerDia2010
  - SDF Analyser
    SDF SUITE
    D-Tech and diagnostic ports
  - Serdia 2010
    Safety-Hints
    Common Hints
    Common Hints – Start and Communication
    Common Hints – Disposability
    Introduction
    Error Hints (FAQ)
    Connection establishment
    Software handling
    Software handling – Topper elements
    Global Programfunctionality – Dataset management
    Global Programfunctionality – Error memory
    Global Programfunctionality – Graphical display
    Global Programfunctionality – Program adjustments
    UseCases EMR4
    Engine settings
    Adjustments engine speed – acceleration pedal
    Exhaust after treatment
    SCRT -TIER4 final
    EOL Test (Tier4F)
    SCR service routines
    DPF service routines
    Service Routines DPF (DOC/SCR)
    Service-Cases
    Other
    UseCases EMR3
    UseCases EMR2
    Programm options
- Commissioning and calibrating the tractor
  - Commissioning procedure (EOL)
  - Electronic Control Unit (ECU) Reset
  - Vehicle model selection
  - Transmission Control Unit (TCU) initialization
  - Electronic Control Unit (ECU) initialization
  - Distributors configuration
  - Maximum vehicle speed
  - Tyre type
  - Language
  - Measurement unit
  - Air brake
  - Front Power Take-Off (PTO)
  - Radar
  - Automatic Air Conditioning
  - iMonitor
  - Isobus
  - MMI
  - Agrosky
  - Front Axle Suspension (FAS)
  - ASM
  - Rear lift 100 mm cylinders
  - Oil pump displacement
  - Front loader (stoll)
  - Engine brake
  - Wet brake
  - Clutch pedal calibration
  - Pneumatic trailer brake
  - Hydraulic trailer brake
  - Valve programming
  - Throttle pedal calibr
  - Hand gas calibration
  - Slope sensor calibration
  - Water mix motor calibration
  - Recirculation Motor calibration
  - Draft sensor calibration
  - Rear hitch position calibration
  - Steering angle calibration
  - Front suspension calibration
  - Front speed sensor
  - Rear Power Take-Off (PTO) calibration
- ECU alarms
  - SDF Severity of alarms
  - ECU ALARMS
- Software management
  - Engine dataset upgrade
  - ECUs firmware update
Method of intervention
- Tools for engine disassembly and reassembly
- Workshop tools for engine disassembly and reassembly (Lv.2)
- Workshop tools for disassembly and reassembly
- B0 – Engine
  - Engine
  - Separating the engine from the transmission (1/2)
  - Separating the engine from the transmission (2/2)
  - Air conditioning compressor belt
  - Water pump / alternator belt
  - Disassembling and assembling alternator (poly-V-belt, level 1)
  - Disassembling and assembling crankcase breather
  - Replacing the crankshaft O-ring (opposite end to flywheel)
  - Disassembling/assembling crankshaft wear sleeve (side opposite flywheel)
  - Disassembling and assembling the front cover (fixing elements)
  - Assembly and disassembly of piston cooling nozzles
  - Assembly and disassembly of piston cooling nozzles
  - Checking the camshaft bearing
  - Removing and refitting crankshaft bearing cap
  - Blanking elements
  - Blanking elements
  - Blanking elements
  - Blanking elements
  - Oil dipstick
  - Oil dipstick
  - Pipe (crankcase breather)
  - Disassembling and assembling the lubricant oil sump (pressed steel sump)
  - Removing and fitting lubricant oil sump (heavy version)
  - Removing and fitting lubricant oil sump (heavy version)
  - Removing and fitting lubricant oil sump (heavy version)
  - Oil filler neck
  - Disassembling and assembling the torsional vibration damper
  - Disassembling and assembling the torsional vibration damper
  - Disassembling and assembling the torsional vibration damper
  - Disassembling and assembling the flywheel (fixing elements)
  - Replacing the starter motor ring gear on the flywheel
  - Removing and fitting the crankshaft
  - Check the crankshaft
  - Check the endfloat of the crankshaft
  - Assembly and disassembly of the crankshaft bearing
  - Check the crankshaft bearings
  - Disassembly and reassembly of connecting rod shank
  - Check the connecting rod shank
  - Disassembling and assembling the piston
  - Check the piston
  - Check the piston
  - Disassembling and assembling the piston rings
  - Check the piston rings
  - Check the piston rings
  - Check the piston rings
  - Compression test
  - Checking compression
  - Disassembling and assembling the cylinder head cover
  - Removing and fitting the cylinder head cover
  - Removing and fitting the cylinder head cover
  - Removing and fitting the cylinder head cover
  - Disassembling and assembling the cylinder head (fasteners)
  - Disassembling and assembling the cylinder head (fasteners)
  - Measuring piston protrusion
  - Assembly and disassembly of the valves
  - Removing and fitting the valves
  - Checking valves, valve guides, valve springs and valve recess
  - Replacing the injector bush
  - Clean the injector bush
  - Clean the injector bush seat
  - Blanking elements (cylinder head)
  - Transport eye-bolt (cylinder head)
  - Transport eye-bolt (cylinder head)
  - Transport eye-bolt (cylinder head)
  - Eye-bolt for transporting (cylinder head)
  - Eye-bolt for transporting (cylinder head)
  - Replace the crankshaft O-ring (flywheel end)
  - Disassembling and assembling the gearbox
  - Assembly and disassembly of the camshaft
  - Check the camshaft
  - Checking and setting valve clearance (6 cylinder)
  - Assembly and disassembly of the distribution valve
  - Removing and refitting the valve timing system
  - Disassembly and assembly of the control elements
  - Disassembling and assembling the oil cooler
  - Removing and fitting the lubricant oil radiator
  - Removing and fitting the lubricant oil radiator
  - Removing and fitting the lubricant oil radiator housing
  - Disassembling and assembling the lubricant oil radiator (blanking elements)
  - Removing and fitting the lubricant oil radiator housing (fastener elements)
  - Blanking elements (lubricant oil cooler housing)
  - Blanking elements (lubricant oil cooler housing)
  - Coolant pipe (lubricant oil radiator housing – crankcase)
  - Coolant pipe (Lubricant oil cooler – cylinder head)
  - Disassembling and assembling the oil suction pipe
  - Disassembly and assembly of the fuel control unit (fastening elements)
  - Disassembly and completion of the fuel control unit
  - Disassembling and completing assembly of the fuel control unit (2000 bar injection system)
  - Disassembling and assembling the high pressure pump (fastener elements)
  - Disassembling and assembling the injector (1600 bar injection system)
  - Disassembling and assembling the injector (1600 bar injection system)
  - Flexible hose connectors
  - Connector plug (fuel delivery pump)
  - Removing and refitting fuel lines (fuel delivery pump – pilot block)
  - Disassembling and assembling the fuel line (fuel control block – high pressure pumps)
  - Disassembling and assembling the rail (1600 bar injection system)
  - Disassembling and assembling the rail (1600 bar injection system)
  - Disassembling and assembling the rail (2000 bar injection system)
  - Disassembling and assembling the pressure cut-off valve (rail)
  - Disassembling and assembling the pressure cut-off valve (rail)
  - Disassembly and assembly of the rail pressure sensor
  - Disassembly and assembly of the rail pressure sensor
  - Removing and refitting fuel lines (Rail, cylinder head, fuel control unit – fuel filter)
  - Fuel pipes (Fuel pump, fuel filter, pilot lock)
  - Fuel pipes (Rail, cylinder head, pilot lock- fuel filter)
  - Vibration damper (installation position)
  - Disassembling and assembling charge air pipe
  - Disassembling and assembling charge air pipe
  - Removing and fitting the coolant pump
  - Disassembling and assembling coolant pipe (ribbed V-belt, level 1)
  - Removing and fitting the coolant pump (fastening elements)
  - Removing and refitting adapter (coolant pump – thermostat housing)
  - Transmission components (coolant pump)
  - V-belt pulley
  - Assembling and disassembling the thermostat
  - Assembling and disassembling the thermostat
  - Disassembling and assembling the thermostat
  - Check the thermostat (after removing)
  - Check the thermostat (after removing)
  - Removal and installation of the thermostat housing
  - Removal and installation of the thermostat housing
  - Removal and installation of the thermostat housing
  - Disassembling and assembling the thermostat housing (fastener elements)
  - Blanking elements (coolant pump – thermostat housing)
  - Blanking elements (thermostat housing)
  - Blanking elements (thermostat housing)
  - Blanking elements (thermostat housing)
  - Blanking elements (thermostat housing)
  - Blanking elements (thermostat housing)
  - Flexible hose fastening (Thermostat housing)
  - Flexible hose connector (thermostat box)
  - Connection (compensation line)
  - Breather pipe (thermostat box – cooler)
  - Pipes (AGR radiator cylinder head)
  - Compensation line (thermostat box)
  - Removing and fitting belt tensioner (ribbed V belt)
  - Disassembly and refitting of the belt tensioner (ribbed V-belt, level 1)
  - Disassembly and refitting of the belt tensioner (ribbed V-belt, level 1)
  - Removal and assembly of the fan support
  - Removal and assembly of the fan support
  - Removal and assembly of the fan support
  - Removal and assembly of the fan support
  - Fastener elements (fan mount)
  - Disassembling and assembling the exhaust manifold
  - Disassembling and assembling the exhaust manifold
  - Removal and installation of the exhaust pipe (auxiliaries)
  - Disassembling and assembling the exhaust manifold
  - Assembling and disassembling the console
  - Disassembling and assembling the butterfly valve
  - Disassembling and assembling the butterfly valves
  - Disassembling and assembling the radiator
  - Removing and fitting the exhaust gas recirculation (EGR) radiator
  - Disassembling and assembling the regulator
  - Disassembling and assembling the regulator
  - Disassembling and assembling the Venturi pipe
  - Disassembling and assembling the Venturi pipe
  - Removing and fitting the pipes (cylinder head – radiator, radiator – cylinder head).
  - Exhaust gas pipe (Venturi tubes – mixing tubes)
  - Pipe (exhaust pipe – pressure transducer)
  - Pipe (exhaust pipe – pressure transducer)
  - Disassembling and assembling the turbocharger
  - Disassembling and assembling the turbocharger
  - Disassembling and assembling the turbocharger
  - Disassembling and assembling the lubricating oil pipe (exhaust gas turbocharger)
  - Disassembling and assembling the lubricating oil pipe (exhaust gas turbocharger)
  - Removing and refitting the lubricant oil return pipe – (upper section) – (turbocharger)
  - Removing and refitting the lubricant oil return pipe – (upper section) – (turbocharger)
  - Disassembling and assembling the lubricating oil return pipe (turbocharger)
  - Removing and refitting the lubricant oil return pipe – (lower section) – (turbocharger)
  - Removing and refitting the lubricant oil return pipe – (lower section) – (turbocharger)
  - Removing and refitting the lubricant oil return pipe – (lower section) – (turbocharger)
  - Disassembling and assembling alternator (poly-V-belt, level 1)
  - Disassembling and assembling alternator (poly-V-belt, level 1)
  - Removing and fitting the V belt pulley/poly-V belt pulley (alternator)
  - Disassembling and assembling the console (ribbed V-belt, level 1)
  - Disassembling and assembling the console (ribbed V-belt, level 1)
  - Disassembling and assembling the console (ribbed V-belt, level 1)
  - Disassembling and assembling the console (ribbed V-belt, level 1)
  - Fitting and removing the rotation device (PTOC)
  - Fitting and removing the rotation device
  - Disassembling and assembling the connector housing
  - Cover (connector casing)
  - Cover (connector casing)
  - Cover (connector casing)
  - Disassembling and assembling the heater
  - Disassembling and assembling the heater
  - Disassembling and assembling the heater
  - Removing and fitting the charge air elbow pipe
  - Disassembling and assembling the mixer pipe
  - Disassembling and assembling the mixer pipe
  - Disassembling and assembling the butterfly valve
  - Disassembling and assembling the butterfly valve
  - Disassembly and assembly of the flange
  - Removing and refitting the diesel particulate filter
  - Removing and fitting the diesel particulate filter (9.5 ” axial and radial system – removed)
  - Disassembling and assembling the NOx sensor
  - Pressure transducer (exhaust back-pressure).
  - Fitting the SCR (Selective Catalytic Reduction) dosing unit
  - Cleaning the SCR delivery pump (Selective Catalytic Reduction)
  - Cleaning/Checking SCR (Selective Catalytic Reduction) metering unit
  - Cleaning the SCR (Selective Catalytic Reduction) pipe (delivery pump – metering unit)
  - Blanking elements (diesel oxidation catalytic converter/diesel particulate filter, SCR catalytic converter)
  - Cover guard (Differential pressure transducer)
  - Mount (Exhaust after-treatment system 9.5″)
  - SCR (Selective Catalytic Reduction) urea solenoid valve
  - SCR delivery pump (Selective Catalytic Reduction)
  - Outlet module particulate filter
  - Mixer pipe (threaded connection) SCR (Selective Catalytic Reduction)
  - Mixer pipe (fastening element) SCR (Selective Catalytic Reduction)
  - Blanking elements (crankcase, PTO-A)
  - Closing elements (Power Take-Off PTO-B)
  - Closing elements (Power Take-Off PTO-B)
  - Blanking elements (gearbox, PTO-C)
  - Blanking elements (gearbox, PTO-C)
- C0 – Engine accessories
  - Engine coolant replacement
  - AdBlue Connection Backflow – Inlet pipes
  - AdBlue tank
  - Intercooler, gearbox oil and fuel exchangers and condenser
  - AdBlue pump module
  - AdBlue 2 way solenoid valve
  - Draining the fuel tanks
  - Main fuel tank
  - Auxiliary tank
  - Bleeding the fuel circuit
  - Auxiliary fuel tank mount
  - Fuel prefilter
  - Air compressor
  - Air compressor disassembly
  - Starter motor
  - Catalytic exhaust silencer
  - DOC (diesel oxidation catalyst) catalytic converter
  - Complete radiator pack
  - Cooler
  - Compensation tank
  - Fan
  - Air filter cartridge
  - Air filter container
  - Removing and fitting the fuel filter head
  - Disassembling and assembling the fuel delivery pump (fastener elements)
  - Fuel filter
  - Manual fuel pump
  - Filter holder
  - Assembly of the pressure transducer (fuel pressure)
  - Disassembly and refitting of the intake air pressure/temperature sender
  - Blanking elements (mixer pipe, intake air)
  - Shield plate (exhaust gas back-pressure sensor)
  - Turbocharger shield plate
  - Support plate (exhaust gas back-pressure relay – sensor)
  - Support (shield plate)
  - Pressure transducer (exhaust back-pressure).
  - Pressure transducer (exhaust back-pressure).
  - Connector manifold (intake air)
  - Connector manifold (intake air)
  - Intake manifold (exhaust gas turbocharger)
  - Removing and fitting the fan mount (fastener elements)
  - Removing and fitting the fan mount (fastener elements)
  - Removing and fitting the temperature sender
  - Removing and fitting the pressure transducer
  - Mount (radiator – exhaust gas recirculation)
  - Mount (radiator – exhaust gas recirculation)
  - Pressure transducer/Duct (exhaust gas back-pressure).
  - Pressure transducer/Duct (exhaust gas back-pressure).
  - Disassembling and assembling the pressure transducer (exhaust back-pressure)
  - Connection (Starter)
  - Connection (Starter)
  - Shield plate (starter)
  - Alternator
  - Starter (fasteners)
  - Mount (Assembly foot, side opposite of the flywheel)
  - Mount (assembly foot, side opposite of the flywheel)
  - Mount (assembly foot, flywheel side)
  - Disassembling and assembling the crankshaft speed sensor (fastener elements)
  - Disassembling and assembling the crankshaft speed sensor (fasteners)
  - Disassembling and assembling the crankshaft speed sensor (fasteners)
  - Disassembling and assembling the camshaft speed sensor (ancillaries)
  - Disassembly and refitting of the intake air pressure/temperature sender
  - Fastener elements (wiring bundle)
  - Fastener elements (wiring bundle)
  - Fastener elements (wiring bundle)
  - Support plate (on the charge air pipe)
  - Support (wiring harness)
  - Temperature sender (coolant)
  - Fitting the pressure transducer (fuel pressure / lubricant oil pressure)
  - Relay (heater, thermo-starter, glow plugs)
  - Connector cable (relay – alternator)
  - Connector cable (relay – heater)
  - Protective cap (relay)
  - Heater (connector line)
  - Check the seal of the cooling system
  - Differential pressure sender (diesel particulate filter)
  - Differential pressure sender (diesel particulate filter)
  - Temperature sender (upstream of the SCR catalytic converter)
  - Temperature sender (ahead of and after diesel oxidation catalytic converter)
  - Temperature sender (exhaust gas)
  - Temperature sender (inlet air and ambient air temperature)
  - V-Band clamp.
  - VBand clamp (4″ exhaust pipe)
  - VBand clamp (turbocharger)
  - Mount (exhaust gas back-pressure sensor)
- D0 – Transmission
  - Torsionally flexible coupling and flywheel
  - Engine-gearbox connector casing
  - Changing the transmission oil
  - Removal of transmission
  - Disassembly of the clutch control block
  - Disassembly of the system control block
  - Disassembly of the pump
  - Separation of the transmission halves
  - Disassembly of the intermediate housing
  - Disassembly of the front wheel drive
  - Disassembly of clutch KV/KR and double gear
  - Disassembly of clutch KV
  - Disassembly of clutch KR
  - Disassembly of the output gear
  - Disassembly of the input shaft (hydrostatic unit)
  - Disassembly of the central shaft (clutch KV/KR)
  - Disassembly of the intermediate gear
  - Disassembly of the multi-disk brake (BG)
  - Disassembly of the drum selector gear (planetary transmission)
  - Disassembly of the ring gear P4/BG and clutch K3/K4
  - Disassembly of planetary drive P4
  - Disassembly of the central shaft
  - Disassembly of clutch K1/K2
  - Disassembly of planetary drive P3
  - Disassembly of planetary drive P2
  - Disassembly of planetary drive P1
  - Disassembly of the hydrostatic unit
  - Reassembly of the clutch housing
  - Reassembly of the hydrostatic unit
  - Reassembly of the drum selector gear (planetary transmission)
  - Reassembly of planetary drive P1
  - Reassembly of planetary drive P2
  - Reassembly of planetary drive P3
  - Reassembly of clutch K1/K2
  - Reassembly of the central shaft
  - Reassembly of planetary drive P4
  - Reassembly of clutch K3/K4 and ring gear P4/BG
  - Reassembly of the multi disk brake (BG)
  - Reassembly of the intermediate housing
  - Reassembly of the input shaft (hydrostatic unit)
  - Reassembly of the intermediate gear
  - Reassembly of the central shaft (clutch KV/KR)
  - Reassembly of the output gear
  - Reassembly of the pump
  - Reassembly of clucth KV/KR
  - Reassembly of clutch KV
  - Reassembly of clutch KR
  - Reassembly of the front wheel drive
  - Joining of the preassembled transmission halves
  - Setting of the axial play drum selector gear/quill shaft (KV/KR) – Axial play= 0.20 … 0.40 mm
  - Setting of the axial play of the KV/KR bearing – Axial play= 0.00 … 0.08 mm
  - Setting of the axial play of the double gear bearing – Axial play= 0.00 … 0.08 mm
  - Setting of the axial play of the front wheel drive – Axial play= 0.025 … 0.1 mm
  - Reassembly of the system control block
  - Reassembly of the clutch control block
  - Reassembly of the speed and inductive sensor
  - Pump Drive flange
  - Disassembly of the Pump Drive flange
  - Adjusting bevel gear set ( … <- )
  - Adjusting bevel gear set ( -> … )
  - Removing the rear pinion
  - PTO clutch
  - Disassembling PTO control clutch
  - Rear power take off unit
  - Disassembling the rear power take off unit
  - Adjustment of selector sleeve position
  - Adjusting the handbrake device
- E0 – Rear axle
  - Separation of the gearbox housing from the rear gearbox housing (1/2)
  - Separation of the gearbox housing from the rear gearbox housing (2/2)
  - RH rear wheel carrier
  - LH rear wheel carrier
  - Disassembly of LH/RH rear axle
  - Adjustment of rear half-shaft bearings
  - Disassembly of the planet carrier
  - Rear differential
  - Disassembly of the rear differential
  - Rear axle brake discs and braking assembly
  - Renewal of brake seals
  - Adjusting the EPB – Bowden assembly
  - Rear brakes
- F0 – Front axle
  - Special tools
  - Special tools
  - Safety information
  - General information
  - Troubleshooting
  - Under-sump reinforcement
  - 4WD shaft
  - Front axle
  - Front axle carrier
  - 4WD shaft cover
  - Carrier with rear axle
  - Safety precautions
  - Oil Draining Mandatory Procedure
  - Pivot brackets
  - Planetary reduction gearbox and steering knuckle housing
  - Stub axle and steering sensor
  - Steering cylinders
  - Differential assembly
  - Conical pinion
  - Pinion seal flange
  - Steering cylinder assembly
  - Planetary reduction gearbox unit
  - Wheel hub unit (without service brake)
  - Wheel hub and brake assembly
  - Beam assembly
  - Carrier assembly
  - Differential carrier assembly (Limited Slip)
  - Differential carrier assembly (Wet Clutch)
  - Differential assembly
  - Differential assembly (wet clutch)
  - Pinion assembly
  - Toe-in/steering angle
  - Post-assembly tests
- G0 – Bodywork – Cab – Platform
  - Empty and charge the air conditioning system
  - Air conditioning compressor
  - A.C. Electronic Control Unit replacement
  - Condenser
  - Front mudguards
  - Main tank mount
  - Battery mount
  - Left hand cab access steps
  - Right hand cab access steps
  - Master cylinder
  - Cab
  - Engine hood
  - Mat
  - Under-seat mat
  - Driver seat
  - Passenger seat
  - Left hand rear pillar cover
  - Right hand rear pillar cover
  - Steering wheel
  - Instrument cluster
  - Right hand control console
  - Left hand console
  - Active carbon filter
  - Cab roof panel trim
  - Park brake control
  - Rear power take off control levers
- H0 – Hydraulic system
  - Draining and filling the auxiliary utility oil tank
  - Auxiliary utility oil tank
  - Bleeding the braking circuit
  - Power steering
  - Power steering pump
  - Front lift control valve
  - Brake system accumulator
  - Rear distributor unit
  - Disassembly of the rear distributor unit (1/2)
  - Disassembly of the rear distributor unit (2/2)
  - Variable displacement L.S. pump
  - Transmission L.S. hydraulic block
  - Brake block
  - Brake control valve
  - Priority valve
  - Resonator
  - Oil delivery line filter
  - Rear differential lock
  - Transmission hydraulic plant heat exchanger
  - Front auxiliary hydraulic distributor
  - Front axle suspension solenoid valve block.
  - Trailer air braking valve
  - Air tanks
  - Air braking system air filter
  - Tightening the hydraulic power steering unit fastener screws
- L0 – Electrical system
  - Instrument cluster
  - Radar
  - Front lift position sensor
  - Front suspension position sensor
  - Inductive position sensor
  - Pressure switch
  - 35 Bar sensor
  - Air filter clogged sensor
  - Clutch pedal sensor
  - Auxiliary utility oil tank pressure switch
  - Auxiliary utility oil tank temperature sensor
  - 63cc oil filter clogging pressure switch
  - Rear lift position sensor
  - Brake control switch
  - Power steering delivery hydraulic system pressure switch
  - Tightening torques for nuts and bolts of electrical connections
- N0 – Front lift
  - Front lift
- R0 – Rear lift
  - Lift cylinders
  - Lift draft sensor
  - Position sensor bushing
  - 3-point linkage
- S0 – Wheels
  - Front Wheels
  - Rear wheels
- V0 – Ballast – towing hitches
  - Tow hook sled
- V1 – AFTERMARKET KITS
  - Installation of the cab pillar filter frames kit (p.n. 9.AB386.91.0)
  - Installation of the connector’s cover kit
  - Pneumatic brake kit – P/N 9.CF089.91.0
Wiring diagrams
- Introduction
  - Introduction
  - Basic electronics for mechanics (1/2)
  - Basic electronics for mechanics (2/2)
  - Electrical and electronic components (1/2)
  - Electrical and electronic components (2/2)
- Components
  - HLHP Control unit (Service Controller Cab)
  - Gear box Control unit
  - ECU ISO 11786 Control unit
  - Service TECU Control unit
  - HLHP Control unit (Service Controller Body)
  - Engine Control unit
  - Remote control unit
  - LED worklights control unit
  - Locations of main ECUs
  - A – Starting and charging
  - B – Fuses
  - C – Grounds
  - D – Intermediate connections
  - E – On-board instruments and visual and audible indicators
  - F – External lights (rotating beacon)
  - G – Interior lights
  - H – Manual electrical controls (steering column stalk)
  - I – Circuit breakers
  - J – Relays
  - K – Sensors and transmitters
  - L – Electromagnets and solenoid valves
  - M – Electrical/electronic devices, Flasher units and Timers
  - N – Electric motors and actuators
  - O – Resistors and rheostats
  - P – Various services
  - R – Diagnostics
- Systems
  - S001 – Power
  - S002 – Starter
  - S003 – Engine cooling
  - S004 – Engine control system
  - S005 – Emissions control system
  - S006 – Front lights
  - S007 – Rear work lights
  - S008 – Roof lights
  - S009 – Front work lights
  - S010 – Sidelights and turn indicators
  - S011 – Internal illumination
  - S012 – Defrost and wiper
  - S013 – Horn
  - S014 – Mirror adjustment
  - S015 – Radio
  - S016 – Power socket – accessories
  - S017 – Air conditioning
  - S018 – Front lift
  - S019 – Rear lift
  - S020 – Rear mudguards
  - S021 – Braking system
  - S022 – Trailer brake
  - S023 – Transmission
  - S024 – Isobus line
  - S025 – “AUX” CAN line
  - S026 – “VEHICLE” CAN line
  - S026A – “BODY” CAN line
  - S027 – Agrosky
  - S028 – i-Monitor
  - S029 – Front axle
  - S030 – Front loader
  - S031 – Prewiring for solenoid valve module
- Wiring harnesses
  - 0.012.2018.4/20 – License plate lights
  - 0.012.4030.4 – Front PTO
  - 0.016.8489.4 – Engine brake
  - 0.017.0496.4/10 – H9 lower front work lights
  - 0.017.0497.4/20 – H9 lower rear work lights
  - 0.017.8425.4 – Trailer socket, EU
  - 0.017.8426.4 – Trailer socket, USA
  - 0.017.9761.4/10 – Distributors 6/7
  - 0.018.2800.4 – Hydraulic trailer braking
  - 0.019.2379.4/20 – Front lights on arm
  - 0.019.2380.4/40 – Hazard warning lights switch (USA)
  - 0.021.2571.4 – ISO 11786
  - 0.019.3659.4 – Monitor (Armrest)
  - 0.019.4559.4/10 – H9 rear work light (service)
  - 0.019.4689.4/20 – H9 roof work lights
  - 0.019.4914.4/20 – LED work lights for cab roof
  - 0.019.5311.4/10 – Automatic A/C system
  - 0.019.9825.4/10 – Inertial SRC40
  - 0.019.9829.4/20 – Antenna – Agrosky SR10
  - 0.020.1009.4 – Front lights on arm (USA)
  - 0.020.8862.4/10 – Roof
  - 0.021.0490.4 – ABS socket for trailer
  - 0.021.1028.4/10 – Agrosky Adapter
  - 0.021.3932.4/10 – ISOBUS module
  - 0.021.5509.4 – Rear screen defrost
  - 0.021.8291.4 – Front lights
  - 0.021.8334.4 – LED rear lights
  - 0.023.0526.4 – TECU wiring loom
  - 0.023.9006.4/10 – Lower fuse box
  - 0.023.9007.4 – Front wiring loom
  - 0.023.9008.4/10 – Cowl
  - 0.023.9010.4/10 – Gearbox
  - 0.023.9011.4/10 – Rear wiring loom
  - 0.023.9201.4/10 – Battery wiring
  - 0.023.9202.4/10 – Front axle steering sensor (Dana)
  - 0.023.9203.4/10 – Front axle steering sensor (Carraro – Agrosky)
  - 0.023.9204.4 – Electrohydraulic steering (Agrosky)
  - 0.023.9205.4 – Electrohydraulic controls
  - 0.023.9206.4 – Prewiring for external solenoid valve module
  - 0.023.9207.4 – Cable adapter on front arm
  - 0.023.9243.4/10 – Front ISOBUS socket
  - 0.023.9244.4/10 – Rear ISOBUS socket
  - 0.023.9245.4 – Front axle steering sensor (Carraro – Basic)
  - 0.023.9246.4 – TECU wiring loom
  - 0.023.9247.4 – Front loader
  - 0.023.9248.4 – Viscostatic fan
  - 0.023.9249.4 – Front loader module
  - 0.023.9250.4 – Rear mudguards
  - 0.023.9567.4/10 – Engine
  - 0.023.9581.4/10 – Cab
  - 0.023.9582.4/10 – LED work lights for cab roof
  - 0.023.9583.4/10 – H9 work lights for cab roof
  - 0.024.0765.4 – Rear screen defrost adapter
  - 0.024.0881.4 – Seat heating
  - 0.024.3197.4/10 – Front axle
  - 04436707 – Flashing light
  - 04437517 – Outline marker lights
Service Info
- A0 – TRACTOR
  - Diagnostics 2026 subscription
  - After-sales 2026 subscription
  - SERVICE NEWS RESEARCH GUIDE
  - Diagnostics 2025 subscription
  - After-sales 2025 subscription
  - Diagnostics 2023 subscription
  - Diagnostics 2024 subscription
  - Diagnostics 2022 subscription
  - Diagnostics 2021 subscription
  - After-sales 2024 subscription
  - After-sales 2023 subscription
  - After-sales 2022 subscription
  - After-sales 2021 subscription
  - After-sales 2019 subscription
  - Diagnostics – 2020 subscription
  - After-sales – 2020 subscription
  - After-sales – 2018 subscription
- B0 – ENGINE
  - Stationary regeneration at T4f engines
  - Deutz AG engine oil specifications
- C0 – ENGINE ACCESSORIES
  - SERVICE NEWS – DEF Unit – Wrong level indication
  - Possible Dust entry at air duct sleeve
  - Diagnostic protocol – AdBlue – Float level unit
  - AdBlue feed pump cleaning
  - AdBlue system trouble shooting
  - Filter and prefilter tool p/n 5.9035.865.0
  - Series 61xx TTV fan improvements
  - AdBlue Float level unit
  - SCR AREA DAMAGED SENSORS
  - eVisco trouble shooting
- D0 – TRANSMISSION
  - Wrong dimension on RPTO stub shaft 21 splines 1-3/8″
  - Power Take Off (PTO) cover
  - RA190 rear PTO rings damage
- F0 – FRONT AXLE
  - Bevel gear set loosing screws
  - Check the front axle steering knuckles for wear
  - Steering behavior check procedure
- G0 – BODYWORK – CAB
  - Brake booster pump internal damage
  - Air conditioning system recharging
  - S2.2 cabin – Door adjustment
  - Fuses & battery box new cover
  - EPB malfunctioning
- H0 – HYDRAULIC AND PNEUMATIC SYSTEM|
  - SERVICE NEWS – Series 6 PS / TTV – noises from orbitrol
  - SERVICE NEWS – HPT – Front axle suspension – Damaged 2.8l accumulator
  - Hydraulic CUNA trailer braking kit (ITALY)
  - Single connection hydraulic braking kit availability update – only for EUROPEAN market
  - Front axle suspension group improvements
  - PVED-CLS replacement
  - Front suspension block diagnostic protocol
  - Trailer brake backup-valve verification
  - Spool valve malfunction
- L0 – ELECTRIC AL SYSTEM