Document overview
Workshop Manual PDF for SAME TIGER 55 → NNZMW602V0BS50001, TIGER (STAGE 5) family. Document language: English; 624 pages.
The corresponding English table of contents contains 42 sections and 209 individual topics.
Main sections included
- Introduction
- Safety
- Technical characteristics
- Calibrations and electronic diagnosis
- Method of intervention
- Wiring diagrams
- Service Info
Document details
- Brand: SAME
- Family: TIGER (STAGE 5)
- Model: TIGER 55
- Starting serial number: NNZMW602V0BS50001
- Document type: Workshop Manual
- Language: English
- Pages: 624
- File size: 232.06 MiB
- Format: Digital PDF download
Compatibility
Before purchasing, verify that your machine model and reference code match SAME TIGER 55 → NNZMW602V0BS50001.
Complete table of contents
Introduction
- Tightening torques
- Pump tightening torques
- Wheel nut/screw tightening torques
- Tightening torques for nuts and bolts of electrical connections
- Installation of solenoid valves and cartridge valves
- Installation of quick couplers
- Units of measurement and conversion factors
Safety
Preface
- Important notes concerning safety
Important safety information
- Recognising hazards
- Indications for persons in contact with the tractor
Safety rules
- Risks during tractor preparation
- Risks during maintenance
- Work on machine systems
- Special disassembly/assembly/inspection procedures
Safety pictograms
- Replacing safety pictograms
Environmental risks
- Hazards associated with the operating environment
Technical characteristics
Engine
- General information
- Tightening Torques
- Technical information
- Lubrificating oil and fuel specification
- Warning
Engine accessories
- Starter motor
Transmission
- Four-wheel drive engagement assembly
Rear axle
- Brakes and rear axle assembly
- Rear differential assembly
Front axle
- Special tools
- Safety precautions
- Maintenance & lubrication
- Exploded view
- Maintenance Points
Hydraulic system
- Hydraulic circuit
- 4-way remote control valve
- Hydrostatic steering
Rear lift
- Rear lift
Calibrations and electronic diagnosis
Diagnostic tools
- D-TECH App
- D-Tech and diagnostic ports
Commissioning and calibrating the tractor
- Commissioning procedure (EOL)
- Cluster configuration
- Measurement unit
- Wheel parameter
- Throttle setting procedure
- Tyre type
ECU alarms
- SDF Severity of alarms
- ECU ALARMS
Software management
- ECUs
- On-board instruments (Cluster/Display) flashing
- ECUs firmware update
Method of intervention
- Special Tool
- Special tools
B0 – Engine
- S/R Cylinders block and liners
- S/R Flyweel
- S/R Crankshaft assembly
- S/R Piston and connecting rods
- S/R Timing case cover
- S/R Rocket shaft assembly
- S/R Valve springs
- S/R Timing case cover and drive
- S/R Cyilinder head cover
- Check & adjust valve tip clearance
- S/R Cylinder head assembly
- S/R Oil pump
- S/R Sump
- Fuel system layout
- S/R High pressure pump
- S/R Water pump
- S/R Inlet mainfold
- S/R Turbocharger
- S/R Alternator
- Separating the complete engine
- Separating the engine from the transmission
- S/R Injector
- S/R Oil filter
C0 – Engine accessories
- S/R Fan belt
- Replacing the coolant
- Complete radiator-heat exchanger pack
- Expansion tank
- Engine fan
- Air filter
- Bleeding the fuel circuit
- S/R Fuel filter element
- Diesel fuel tank
- S/R Starter motor
- S/R Exhaust manifold
- Drain pipe
- Intermediate manifold
- Electrical & electronic control system
D0 – Transmission
- Draining and filling the transmission oil
- Clutch
- Clutch plate wear check
- Disassembly of the gearbox input shaft
- Pressure plate assembly
- Shimming the bearing on the secondary shaft and the gears on the primary shaft
- Disassembly of the main shaft
- Disassembly of the secondary shaft
- Separating front gearbox housing from rear gearbox housing
- Gear lever cover
- Gear lever cover
- Gear shifter rods and fork assembly
- Conical screw assembly
- Internal range reduction gear controls
- Rear pinion casing
- PTO output shaft
- 4WD shaft in transmission
E0 – Rear axle
- Axle casing
- Disassembling rear axle
- Right-hand rear axle
- Left-hand rear axle
- Disassembling the planetary gear unit
- Rear differential
- Adjusting the bevel gear set and the rear differential
- Correct assembly of differential pins
- Brake carriers
- Removing the rear differential
- Rear differential lock control fork
- Bleeding air from the hydraulic brake system
- Rear brake discs
F0 – Front axle
- Pinion-differential assembly
- Carrier with front axle
- Front axle
- Front axle adjusting endfloat
- Steering cylinders
- Disassembling the steering cylinder
- Complete steering knuckle housing
- Adjusting bearing preload
- Differential assembly
- Assembly and adjustment of the front differential of SDF axles
- Differential lock
- 4WD shaft
- Adjustment of the bevel gear set
- Removing bevel gear set
- Adjustment of the differential preload
- Disassembly of the differential
- Differential locking device adjustment
- Adjusting pinion position
- Adjusting pinion/crown wheel backlash
- Adjusting pinion bearing preload
- Wheel hub bearing shims
- Planetary reduction gearbox
- Disassembly of the planetary reduction gearbox
- Front brake discs
- Front axle brake piston
- Front axle
- Differential assembly adjustment
- Steering Cylinder Removal
- Tie Rod Removal
- Drain Plug Removal
- Final drive cover disassembly
- Final drive cover installation
- Drop shaft disassembly
- Drop shaft assembly & installation
- Knuckle housing removal
- Knuckle housing installation
- Face seal installation
- Shoulder housing removal & disassembly
- Shoulder housing assembly
- Carrier removal & disassembly
- Carrier assembly & installation
- Wheel end installation
- Tie Rod Installation
- Steering cylinder installation
- Toe-in adjustment
- Assemble Rear Trunnion
- Assemble Front Trunnion
- Axle Installation & End Play Adjustment
- Driveshaft & Hydraulic Line Installation
G0 – Bodywork – Cab – Platform
- Engine hood
- Lower hood guard
- Platform
- Underseat plate
- Cab access steps
- Rear mudguards
- Front mudguard
- Instrument panel
- Dashboard
- Lower dashboard guard
- Upper dashboard guard
- Guard panels
- Roof
- Driver seat
- Steering wheel
- Roll bar
H0 – Hydraulic system
- Hydrostatic steering (orbitrol)
- Rear auxiliary utility distributor
L0 – Electrical system
- Battery
R0 – Rear lift
- Rear lift
- Adjustment of the rear lift
S0 – Wheels
- Front Wheels
- Rear wheels
V0 – Ballast – towing hitches
- Front ballasts and support
- Draw-bar
Wiring diagrams
Wiring harnesses
- Wiring looms
- W-TECH – ELECTRICAL SECTION
Service Info
A0 – TRACTOR
- Diagnostics 2026 subscription
- After-sales 2026 subscription
- SERVICE NEWS RESEARCH GUIDE
- Diagnostics 2025 subscription
- After-sales 2025 subscription
- Diagnostics 2024 subscription
- After-sales 2024 subscription
B0 – ENGINE
- FARMotion seal ring leakage
C0 – ENGINE ACCESSORIES
- Diagnostic protocol – AdBlue – Float level unit
- Filter and prefilter tool p/n 5.9035.865.0
F0 – FRONT AXLE
- Bevel gear set loosing screws
H0 – HYDRAULIC AND PNEUMATIC SYSTEM|
- Hydraulic CUNA trailer braking kit (ITALY)
- Single connection hydraulic braking kit availability update – only for EUROPEAN market
L0 – ELECTRIC AL SYSTEM
- Electronic diagnosis of Simpson engines (Turkish market)
- PTO switch not working
V1 – AFTERMARKET KITS
- Check correct installation of braking KIT
- Instructions for kit aftersales
