Document overview
Workshop Manual PDF for SAME LASER 130 → S33S306WVT2E10001, LASER family. Document language: English; 838 pages.
The corresponding English table of contents contains 47 sections and 254 individual topics.
Main sections included
- Introduction
- Safety
- Technical characteristics
- Calibrations and electronic diagnosis
- Method of intervention
- Wiring diagrams
- Service Info
Document details
- Brand: SAME
- Family: LASER
- Model: LASER 130
- Starting serial number: S33S306WVT2E10001
- Document type: Workshop Manual
- Language: English
- Pages: 838
- File size: 135.85 MiB
- Format: Digital PDF download
Compatibility
Before purchasing, verify that your machine model and reference code match SAME LASER 130 → S33S306WVT2E10001.
Complete table of contents
Introduction
- Introduction – Engines
- Tightening Torques
- Tightening torques for nuts and bolts of electrical connections
- Wheel rim to hub screws and nuts tightening torques
- Installation of solenoid valves and cartridge valves
- Installation of quick couplers
- Units of measurement and conversion factors
- Identification of the engine type and serial number position, Europe version
- Identification of the engine type and serial number position, EPA version
- Identification of the injection pump type
- Injector type identification
Safety
Preface
- Important notes concerning safety
Important safety information
- Recognising hazards
- Indications for persons in contact with the tractor
Safety rules
- Risks during tractor preparation
- Risks during maintenance
- Work on machine systems
- Special disassembly/assembly/inspection procedures
Safety pictograms
- Replacing safety pictograms
Environmental risks
- Hazards associated with the operating environment
Technical characteristics
Engine
- Engine block technical data – cylinders
- Crankshaft technical data
- Piston technical data – Piston rings
- Connecting rod technical data
- Camshaft technical data – static advance of 13°
- Camshaft technical data – static advance of 16°
- Timing gears technical data
- Technical data and dimensions of valves – valve springs
- Technical data and dimensions of cylinder heads – valve guides – valve seats
- Technical data and dimensions of rocker arms – rocker shafts – tappets
- Engine injector technical data (with turbocharger)
- Hydraulic tappets diagram
Engine accessories
- Starter motor
Transmission
- Transmission
- Rear PTO
- Hydraulic rear PTO clutch
Rear axle
- Rear axle
- Rear axle
Front axle
- Front axle
Hydraulic system
- Hydraulic pumps
- Power steering valve
- Remote control valve
- Braking system
- Hydraulic trailer braking system
- Hydraulic trailer braking valve
- Pressure limiting valve
Electrical equipment
- Alternator
Rear lift
- Lift hydraulic control valve
Calibrations and electronic diagnosis
Diagnostic tools
- ECU interrogation
SDF Analyser
- SDF Analyser
- SDF Analyser – Diagnostic socket
Diagnostic tool screens
- ART/PC tester screens for the engine ECU
Commissioning and calibrating the tractor
- Commissioning the engine ECU – Presentation screen
- Commissioning the engine ECU – Main menu
- Commissioning the engine ECU – Configuration menu
ECU alarms
Engine alarms
- Alarms – Engine alarms list
Method of intervention
B0 – Engine
- Preliminary and final operations
- Final engine checks
- Checking engine block
- Crankshaft
- Crankshaft checks
- Flywheel checks
- Renewal of crankshaft rear oil seal
- Pistons and cylinder liners
- Pistons and rings check
- Cylinder liners check
- Check connecting rods – gudgeon pins – rod cap screws
- Camshaft
- Camshaft checks
- Timing gear checks
- Adjusting timing gears backlash
- Valve timing
- Valves check
- Valve seats check
- Valves sealing check
- Valves adjustment
- Valve guides check and replacement
- Inspecting the rocker arms and rocker shafts
- Cylinder heads
- Heat exchanger removal
- Valve springs check
- Disassembly of the heat exchanger
- Lubrication pump
- Lubrication pump disassembly
- Oil sump
- INJECTION PUMPS, GOVERNOR AND FUEL SUPPLY
- Synchronising injection pumps
- Injectors assembly
- Injectors check
- Checking injectors protrusion – Renewal of copper bushes
- Injection pumps control rod
- Injection pump control rod
- Overhaul of the mechanical governor (standard and with LDA valve)
- Overhaul of the mechanical governor gear
- Electronic governor adjustment
- Installation of mechanical governor drive unit and electronic governor support
- Installation of electronic governor support
- Engine coolant pump
- Thermostatic valve
- Checking the thermostat valve
- Cooling and intake ducts
D0 – Transmission
- Checking the transmission oil level
- Changing the transmission oil
- Changing the transmission oil filters
- Range selector assembly
- Clutch plate
- Connector housing
- Shuttle shaft
- Primary shaft
- Secondary shaft
- Gearbox and mechanical shuttle – Complete assembly
- Disassembly of the gearbox synchronizers
- Adjustment of the Rear Bevel Gear Pair
- 4WD output shaft
- Disassembly of the PTO clutch
- PTO clutch and pump
- Disassembly of the PTO clutch pump
- PTO input shaft
- PTO output shaft
- Parking brake shoes
E0 – Rear axle
- Rear axle (Removal – Refitting)
- Disassembly of the rear axle
- Rear differential
- Bleeding the hydraulic braking system
- Rear axle brake discs and piston
- Adjustment of the preload on the rear axle taper roller bearings
F0 – Front axle
- Front axle pivot brackets
- Front axle – Complete assembly
- Adjustment of front axle end float
- Steering cylinders
- Steering knuckle housing and half-shaft
- Checking toe-in
- Bevel gear pair
- Adjustment of the bevel gear pair
- Disassembly of the front axle differential
- Propeller shaft – Front axle drive shaft
- Planetary reduction gear
- Front axle brake discs and piston
G0 – Bodywork – Cab – Platform
- Adjustment of the rear lift position control – external controls
H0 – Hydraulic system
- Services pump
- Disassembly of the hydraulic services pump
- Power steering disassembly
R0 – Rear lift
- Disassembly of the rear lift – complete assembly
- Lift arms
- Lift control valve
- Adjustment of the rear lift position control – internal controls
- Adjustment of draft control
- Adjustment of the lift sensitivity
- Draft sensor
- Disassembly of the draft sensor
S0 – Wheels
- Front wheels
- Rear wheels
V0 – Ballast – towing hitches
- Support and towing hitch
Wiring diagrams
Introduction
- Introduction
- Basic electronics for mechanics (1/2)
- Basic electronics for mechanics (2/2)
- Electrical and electronic components (1/2)
- Electrical and electronic components (2/2)
Components
- A – Starting and charging
- B – Fuses
- C – Grounds
- D – Intermediate connections
- E – On-board instruments and visual and audible indicators
- F – External lights
- G – Interior lights
- H – Electrical and manual controls
- I – Circuit breakers
- J – Relays
- K – Sensors and transmitters
- L – Electromagnets and solenoid valves
- M – Electrical/electronic devices, flasher units and timers
- N – Electric motors and actuators
- O – Resistors, rheostats, diodes and diode boards
- P – Various services
- T – Power supply points (+15 o +30)
Systems
- S001 – Starting and preheating – cab version
- S002 – Starting and preheating – platform version
- S003 – Electronic engine governor – Cab version
- S004 – Electronic engine governor – Platform version
- S005 – Diagnostics and accessories – Cab version
- S006 – Diagnostics and accessories – Platform version
- S007 – Instrument panel – Cab version
- S008 – Instrument panel – Platform version
- S009 – Manual air conditioner
- S010 – Road lights – Cab version
- S011 – Road lights – Platform version
- S012 – Power feed (+15) – Cab version
- S013 – Power feed (+30) – Cab version
- S014 – Power feed (+15) – Platform version
- S015 – Power feed (+30) – Platform version
- S016 – Lights selector switch – Cab version
- S017 – Lights selector switch – Platform version
- S018 – Braking – Cab version
- S019 – Braking – Platform version
- S020 – Accessories – cab version
- S021 – Accessories – platform version
- S022 – Windscreen wipers
- S023 – Work lights
- S024 – Work lights – Platform version
Wiring harnesses
- 0.009.6934.3/10 – Work light and rotating beacon
- 0.011.3824.4/10 – Rotating beacon
- 0.013.9827.4/90 – Roof
- 0.014.3927.4/40 – Lower front work lights on RH side of cab
- 0.014.3927.4/40 – Lower front work lights on LH side of cab
- 0.014.8355.4/20 – RH lower headlights
- 0.014.8355.4/20 – LH lower headlights
- 0.016.9824.4/20 – Front wiring loom
- 0.016.9825.4/10 – Preheating
- 0.016.9826.4/20 – Rear wiring loom
- 0.016.9827.4/20 – Underfloor wiring loom
- 0.016.9828.4/20 – Preheat – For cold climates
- 0.016.9829.4/20 – Central wiring loom
- 0.016.9830.4/10 – Central wiring loom – Platform version
- 0.016.9831.4/20 – Underfloor wiring loom – Platform version
- 0.016.9832.4/10 – Engine governor
- 0.016.9833.4/10 – Engine governor – Platform version
- 0.255.8454.3/20 – License plate light
- 0.900.0035.5 – Manual A/C system
Service Info
A0 – TRACTOR
- Diagnostics 2026 subscription
- After-sales 2026 subscription
- SERVICE NEWS RESEARCH GUIDE
- Diagnostics 2025 subscription
- After-sales 2025 subscription
- Diagnostics 2023 subscription
- Diagnostics 2024 subscription
- Diagnostics 2022 subscription
- Diagnostics 2021 subscription
- Technical Documentation DVD 06/2009
- SDF LUBRICANTS: Lubricant oils and coolant fluids
- After-sales 2024 subscription
- After-sales 2023 subscription
- After-sales 2022 subscription
- After-sales 2021 subscription
- After-sales 2019 subscription
- SDF Parts and SDF Service DVV 04/2014, version 26
- Technical Documentation DVD 03/2010
- New function: Download PDF manuals
- Diagnostics – 2020 subscription
- After-sales – 2020 subscription
- After-sales – 2018 subscription
- Service and Spare Parts – 2017 Subscription
- SDF Parts and SDF Service DVDs 05/2014 version 25
- SDF Parts and SDF Service DVDs 03/2013 version 24
B0 – ENGINE
- Flushing the lubrication circuit
- Deutz AG engine oil specifications
C0 – ENGINE ACCESSORIES
- Diagnostic protocol – AdBlue – Float level unit
- Filter and prefilter tool p/n 5.9035.865.0
D0 – TRANSMISSION
- Extremely stiff range selector
- Main clutch disc
F0 – FRONT AXLE
- Check the front axle steering knuckles for wear
- Steering behavior check procedure
G0 – BODYWORK – CAB
- Air conditioning system recharging
H0 – HYDRAULIC AND PNEUMATIC SYSTEM|
- Hydraulic CUNA trailer braking kit (ITALY)
- Single connection hydraulic braking kit availability update – only for EUROPEAN market
- L0 – ELECTRIC AL SYSTEM
