Document overview
Workshop Manual for LAMBORGHINI SPARK 210 VRT → WSXLL40200LL10001 from the SPARK VRT (STAGE 5) family. Digital PDF in English with 2,164 pages.
The corresponding English table of contents contains 51 sections and 762 individual topics.
Main sections included
- Introduction
- Safety
- Technical characteristics
- Calibrations and electronic diagnosis
- Method of intervention
- Wiring diagrams
- Service Info
Document details
- Brand: LAMBORGHINI
- Family: SPARK VRT (STAGE 5)
- Model: SPARK 210 VRT
- Starting serial number: WSXLL40200LL10001
- Document type: Workshop Manual
- Language: English
- Pages: 2,164
- File size: 589.57 MiB
- Format: Digital PDF download
Compatibility
Before purchasing, verify that your machine model and reference code match LAMBORGHINI SPARK 210 VRT → WSXLL40200LL10001.
Complete table of contents
Introduction
- Tightening torques
- Wheel nut/screw tightening torques
- Tightening torques for nuts and bolts of electrical connections
- Installation of solenoid valves and cartridge valves
- Installation of quick couplers
- One-way valves
- Fixing the steering wheel
- Spool valves
- Units of measurement and conversion factors
Safety
Preface
- Important notes concerning safety
Important safety information
- Recognising hazards
- Indications for persons in contact with the tractor
Safety rules
- Risks during tractor preparation
- Risks during maintenance
- Work on machine systems
- Special disassembly/assembly/inspection procedures
Safety pictograms
- Replacing safety pictograms
Environmental risks
- Hazards associated with the operating environment
Technical characteristics
- External views
- Viste interni cabina
- Dimensions and weights of the tractor
- Main technical data
Engine
- Pressure transducer (exhaust gas backpressure) – (B60)
- Pressure transducer (ahead of SCR catalytic converter) – (B88)
- Differential pressure transducer (diesel particulate filter) – (B61)
- Differential pressure transducer (diesel particulate filter) – (B58)
- Pressure sensor (Rail) – (B49)
- Pressure transducer (lubricant oil) – (B6) / (fuel) – (B51)
- Pressure transducer (ahead of SCR catalytic converter) – (B88)
- Pressure transducer
- Pressure transducer
- Pressure/temperature sender (engine intake air) – (B48)
- Pressure/temperature sender (engine intake air) – (B48)
- Temperature sender (exhaust gas recirculation) – (B64)
- Temperature sender (intake air, ambient air) – (B74)
- Temperature sender (ahead of and after diesel oxidation catalyst) – (B65)
- Temperature sender (ahead of and after diesel oxidation catalyst) – (B65)
- Temperature sender (ahead of SCR catalytic converter) – (B78)
- Temperature sender (ahead of SCR catalytic converter) – (B78)
- Speed sensor (crankshaft) – (B40.2)
- Speed sensor (camshaft) – (B40.1) / (crankshaft) – (B40.2)
- Speed sensor (camshaft) – (B40.1)
- NOx sensor (SCR ahead of catalytic converter) – (B54)
- NOx sensor (SCR ahead of catalytic converter) – (B54)
- NOx sensor (SCR ahead of catalytic converter) – (B54)
- NOx sensor (SCR after catalytic converter) – (B56)
Engine accessories
- Expansion tank
- Coolant radiator
- Air filter
- Intercooler
- Diesel radiator
- Diesel fuel tank
- Diesel pre-filter
- AdBlue tank
- AdBlue float
Transmission
- Modular architecture transmission
- Modular architecture transmission
Rear axle
- Rear axle
- Rear brakes
- Air braking
- Rear PTO
- Checking and topping up the oil level of the rear final drive units
Front axle
- General characteristics
Bodywork – Cab – Platform
- Air conditioning system
- Instrument cluster
- Right-hand console
- Front console and cab pillars
- Multifunction armrest
- Roof panel
- Left hand console
- Openable roof hatch
- Ballasts – Technical data
- Ballasts
- Drawbar
Hydraulic system
- Base hydraulic circuit
- Full house hydraulic circuit
- Optional hydraulic circuit
- Optional hydraulic circuit 1
- Optional hydraulic circuit 2
- Optional hydraulic circuit 3
- Transmission hydraulic circuit 1
- Transmission hydraulic circuit 2
- Base hydraulic circuit
- Full house hydraulic circuit
- Optional hydraulic circuit
- Optional hydraulic circuit 1
- Optional hydraulic circuit 2
- Transmission hydraulic circuit 1
- Transmission hydraulic circuit 2
- Hydraulic pumps
- Auxiliary utility oil tank
- 22,5 cc variable displacement pump
- RH variable displacement pump, 22.5 + 40 cc
- Variable displacement pump 22.5 + 40 cc + 11 cc
- 45 cc variable displacement pump
- 63 cc variable displacement pump
- Oil delivery filter 50 bar
- Orbitrol 70/270
- Orbitrol 70/230 LSRM
Front PTO
- Front PTO
Front lift
- Front lift
Rear lift
- Rear lift
Calibrations and electronic diagnosis
- ECUs
Diagnostic tools
- D-Tech and diagnostic ports
- D-TECH App
- ECUs
Commissioning and calibrating the tractor
- Commissioning procedure (EOL)
- ECU Reset
- Set vehicle model
- Transmission Control Unit (TCU) initialization
- ECUs initialization
- Distributors configuration
- Maximum vehicle speed
- Tyre type
- Language
- Measurement unit
- Front Power Take-Off (PTO)
- Radar
- Automatic Air Conditioning
- iMonitor
- ISO 11786
- Iso 11783
- MMI (man machine interface)
- Agrosky
- Font Susp.
- ASM (Automatic Steering Management)
- Front speed sensor
- Oil pump displacement
- Stoll
- Engine brake
- Front Wet brake
- Pneumatic trailer brake
- Pneumatic trailer brake MR
- Rear PTO
- Radio CAN
- PTO front ratio configuration
- GTECU init
- Distributors command calibration neutral
- eTCV parameters configuration
- Clutch pedal calibration
- Throttle pedal calibration
- Hand gas calibration
- Park brake parameter configuration
- Slope sensor calibration
- Water mix motor calibration
- Recirculation Motor calibration
- Draft sensor calibration
- Rear hitch position calibration
- Steering angle calibration
- Front hitch calibration
- Front suspension calibration
- Wheel angle sensor calibration
- PVED-CL Valve spool calibration
ECU alarms
- SDF Severity of alarms
- ECU ALARMS
Software management
- Engine dataset upgrade
Method of intervention
B0 – Engine
- V-belt pulley
- Disassembly and refitting of the belt tensioner (ribbed V-belt, level 1)
- Disassembly and refitting of the belt tensioner (ribbed V-belt, level 1)
- Removal and assembly of the fan support
- Removal and assembly of the fan support
- Disassembly and assembly of fan mount
- Removal and assembly of the fan support
- Fastener elements (fan mount)
- Removing and fitting the belt tensioner (ribbed V-belt, level 2)
- Checking crankcase pressure
- Removing and fitting the crankcase breather
- Disassembling and assembling crankcase breather
- Removing and fitting the crankcase breather
- Removing and fitting the crankcase breather
- Removing and fitting the crankcase breather
- Removing and fitting the crankcase breather
- Blanking tools (crankcase, electronic engine governor)
- Blanking elements
- Fastener elements (crankcase)
- Blanking tool (crankcase)
- Mount (crankcase breather)
- Pipe (crankcase breather)
- Support (Assembly foot, opposite side to flywheel)
- Fitting and removing the rotation device
- Fitting and removing the rotation device (PTOC power take off)
- Blanking elements (crankcase, PTO-A)
- Blanking elements (crankcase, PTO-A)
- Fastener elements (gearbox, PTOC power take off)
- Fastener elements (gearbox, PTOC power take off)
- Fastener elements (PTO-B power take off)
- Blanking elements (PTO-B)
- Blanking elements (PTO-B)
- Disassembling and assembling the connector housing
- Cover (connector casing)
- Cover (connector casing)
- Cover (connector casing)
- Replacing crankshaft seal ring (side opposite flywheel).
- Fitting and removing the crankshaft sleeve (side opposite flywheel)
- Disassembling and assembling the front cover (fixing elements)
- Checking the camshaft bearing
- Removing and fitting and the crankshaft bearing cap
- Removing and fitting the V belt pulley/poly-V belt pulley
- Removing and fitting the torsional vibration damper
- Disassembling and assembling the torsional vibration damper
- Removing and fitting the torsional vibration damper
- Disassembling and assembling the flywheel (fixing elements)
- Replacing the starter motor ring gear of the flywheel
- Fitting and removing the crankshaft bearings
- Checking the crankshaft
- Check the endfloat of the crankshaft
- Fitting and removing the crankshaft bearings
- Checking the crankshaft bearings
- Removing and fitting the sensor wheel
- Replacing the crankshaft seal ring (flywheel side)
- Removing and fitting the connecting rod shank
- Checking the connecting rod shank
- Disassembling and assembling the piston
- Disassembling and assembling the piston rings
- Check the piston rings
- Check the piston rings
- Check the piston rings
- Measuring piston protrusion
- Checking compression
- Removing and fitting the cylinder head cover
- Removing and fitting the cylinder head cover
- Disassembling and assembling the cylinder head (fasteners)
- Removing and fitting the valves
- Checking valves, valve guides, valve springs and valve recess
- Blanking elements (cylinder head)
- Transport eye-bolt (cylinder head)
- Transport eye-bolt (cylinder head)
- Transport eye-bolt (cylinder head)
- Checking and setting valve clearance (6 cylinder)
- Assembly and disassembly of the distribution valve
- Removing and refitting the valve timing system
- Disassembly and assembly of the control elements
- Oil dipstick
- Oil dipstick
- Removing and fitting the lubricant oil sump (pressed steel lubricant oil sump)
- Disassembling and assembling the lubricant oil sump (pressed steel sump)
- Removing and fitting lubricant oil sump (heavy version)
- Removing and fitting lubricant oil sump (heavy version)
- Removing and fitting lubricant oil sump (heavy version)
- Oil filler neck
- Removing and fitting lubricant oil cooler
- Removing and fitting lubricant oil cooler (fastener elements)
- Removing and fitting the lubricant oil cooler
- Removing and fitting lubricant oil cooler
- Removing and fitting the lubricant oil cooler housing
- Removing and fitting the lubricant oil cooler housing (fastener elements)
- Blanking elements (lubricant oil cooler housing)
- Fastener elements (lubricant oil cooler housing)
- Fastener elements (lubricant oil cooler housing)
- Coolant pipe (lubricant oil radiator housing – crankcase)
- Coolant pipe (lubricant oil cooler – cylinder head)
- Removing and fitting the oil suction pipe
- Replacing the injector bush
- Cleaning the injector bush
- Cleaning the injector bush seat
- Disassembly and assembly of the fuel control unit (fastening elements)
- Disassembling and completing assembly of the fuel control unit (2000 bar injection system)
- Disassembly and completion of the fuel control unit
- Disassembling and assembling the high pressure pump (fastener elements)
- Removing and fitting the injector (1600 bar injection system)
- Removing and fitting the injector (1600 bar injection system)
- Removing and fitting the injector (2000 bar injection system)
- Removing and fitting the fuel filter console (bowl)
- Removing and fitting the fuel pump (fastener elements)
- Flexible hose connectors
- Fuel filter
- Fuel filter
- Fuel filter
- Fuel filter
- Connector plug (fuel delivery pump)
- Removing and fitting the fuel lines (fuel pump – pilot block)
- Removing and fitting the fuel line (pilot block high pressure pumps)
- Disassembling and assembling the rail (1600 bar injection system)
- Removing and fitting the rail (1600 bar injection system)
- Removing and fitting the rail (1600 bar injection system)
- Fitting and removing the pressure limiting valve (Rail)
- Fitting and removing the pressure limiting valve (Rail)
- Fitting and removing the rail pressure sensor
- Removing and refitting fuel lines (Rail, cylinder head, fuel control unit – fuel filter)
- Fuel pipe (fuel filter – pilot block)
- Fuel pipe (rail, cylinder head, pilot block)
- Fuel pipe (fuel delivery pump, fuel filter, pilot block)
- Fuel pipes (Rail, cylinder head, pilot lock- fuel filter)
- Vibration damper (assembly position)
- Pressure transducer (exhaust gas backpressure)
- Pressure transducer (exhaust gas backpressure)
- Assembly and disassembly of piston cooling nozzles
- Assembly and disassembly of piston cooling nozzles
- Removing and fitting the coolant pump
- Removing and fitting the coolant pump (V-belt, level 1)
- Removing and fitting the coolant pump (fastening elements)
- Removing and fitting the coolant pump
- Removing and fitting the coolant pump
- Removing and refitting adapter (coolant pump – thermostat housing)
- Transmission components (coolant pump)
- Removing and fitting the thermostat
- Disassembling and assembling the thermostat
- Removing and fitting the thermostat
- Check the thermostat (after removing)
- Check the thermostat (after removing)
- Removing and fitting the thermostat housing (fastener elements)
- Removal and installation of the thermostat housing
- Removal and installation of the thermostat housing
- Removal and installation of the thermostat housing
- Fastener elements (coolant pump thermostat housing)
- Fastener elements (thermostat housing)
- Blanking elements (thermostat housing)
- Blanking elements (thermostat housing)
- Fastener elements (thermostat housing)
- Fastener elements (thermostat housing)
- Flexible hose fastening (Thermostat housing)
- Flexible hose connector (thermostat box)
- Fitting (compensation line)
- Breather pipe (thermostat box – cooler)
- Pipes (EGR radiator cylinder head)
- Pipes (EGR radiator cylinder head)
- Compensation line (thermostat box)
- Connector cable (intake air)
- Removing and refitting the diesel particulate filter
- Removing and fitting the turbocharger
- Removing and fitting the turbocharger
- Removing and fitting the turbocharger
- Disassembling and assembling the lubricating oil pipe (exhaust gas turbocharger)
- Disassembling and assembling the lubricating oil pipe (exhaust gas turbocharger)
- Removing and fitting the lubricant oil return pipe (upper section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (upper section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (upper section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (lower section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (lower section) (Turbocharger)
- Removing and fitting the lubricant oil return pipe (lower section) (Turbocharger)
- Cover guard (Differential pressure transducer)
- Disassembling and assembling the heater
- Disassembling and assembling the heater
- Disassembling and assembling the heater
- Removing and fitting the charge air elbow pipe
- Disassembling and assembling the mixer pipe
- Disassembling and assembling the mixer pipe
- Disassembling and assembling the butterfly valve
- Disassembling and assembling the butterfly valve
- Disassembly and assembly of the flange
- Removing and refitting the diesel particulate filter
- Mixer pipe (threaded connection) SCR (Selective Catalytic Reduction)
- Mixer pipe (fastening element) SCR (Selective Catalytic Reduction)
- Disassembling and assembling alternator (poly-V-belt, level 1)
- Disassembling and assembling the console (ribbed V-belt, level 1)
- Disassembling and assembling the console (ribbed V-belt, level 1)
- Disassembling and assembling the crankshaft speed sensor (fasteners)
- SCR delivery pump (Selective Catalytic Reduction)
C0 – Engine accessories
- Removing and fitting the fan mount (fastener elements)
- Mount (assembly foot, side opposite of the flywheel)
- Mount (assembly foot, flywheel side)
- Manual fuel pump
- Assembly of the pressure transducer (fuel pressure)
- Check the seal of the cooling system
- Intake manifold (exhaust gas turbocharger)
- Disassembly and refitting of the intake air pressure/temperature sender
- Fastener elements (wiring bundle)
- Fastener elements (wiring bundle)
- Mount (fasteners)
- Support plate (on the charge air pipe)
- Mounting plate (on boost air hose)
- Cable harness (fastener elements)
- Protective cap (relay)
- Heater (connector line)
- Flushing the SCR (Selective Catalytic Reduction) delivery pump
- Flushing/Checking SCR (Selective Catalytic Reduction) metering unit
- Flushing the SCR (Selective Catalytic Reduction) pipe (delivery pump – metering unit)
- Fitting (starter motor)
- Fitting (starter motor)
- Shield plate (starter motor)
- Shield plate (starter)
- Starter (fasteners)
- Removing and refitting the diesel particulate filter (module size 9.5″)
- Fastener elements (exhaust aftertreatment system) (NOx sensor, temperature sender, diesel particulate filter differential pressure sender)
- Mount (module size 9.5”)
- V-Band clamp.
- VBand clamp (3″ exhaust pipe)
- VBand clamp (4″ exhaust pipe)
- Inlet module (module size 9.5″)
- Outlet module (module size 9.5″)
- Mixer pipe (threaded connection)
- Alternator
- Alternator
- Removing and fitting the rotational speed sensor (crankshaft)
- Disassembling and assembling the crankshaft speed sensor (fasteners)
- Disassembling and assembling the camshaft speed sensor (ancillaries)
- Disassembly and refitting of the intake air pressure/temperature sender
- Temperature sender (coolant)
- Fitting the pressure transducer (fuel pressure / lubricant oil pressure)
- Heater relay
- Relay (heater, thermo-starter, glow plugs)
- Disassembling and assembling the NOx sensor
- Disassembling and assembling the pressure transducer (exhaust back-pressure)
- Assembling the SCR (Selective Catalytic Reduction) metering unit
- Differential pressure sender (diesel particulate filter)
- Differential pressure sender (diesel particulate filter)
- Temperature sender (upstream of the SCR catalytic converter)
- Temperature sender (ahead of and after diesel oxidation catalytic converter)
- Temperature sender (exhaust gas)
- Temperature sender (inlet air and ambient air temperature)
- SCR (Selective Catalytic Reduction) solenoid valve
- Connector cable (relay – alternator)
- Connector cable (relay – heater)
- Replacing the engine coolant
- Bleeding the fuel circuit
- Engine air fan
- Water radiator
- Removing the water radiator
- Complete cooling pack
- Diesel radiator
- Transmission oil radiator
- Intercooler and gearbox oil / fuel heat exchanger
- Engine air filter
- Engine air intake pipe
- Diesel fuel tank
- Diesel pre-filter
- AdBlue tank
- AdBlue pump
D0 – Transmission
- Changing the transmission oil
- General repair instructions
- Tightening Torques
- Adjusting unit
- Control unit
- Control block
- Sensors on the gearbox housing
- Wiring loom
- Valve blocks (clutch control)
- Piping
- Hydraulic module
- Removing and installing the gearbox
- Gearbox
- Pump drive gear carrier
- Transmission oil level
- Assembling 4WD manifold
- Fitting 4WD clutch
- PTO ring nut / PTO shafts
- Fitting PTO control rods
- Tightening the gearbox flange screws
- Tightening screws of PTO flange and top link
- Fitting and testing the PTO clutch
- Installing PTO cartridge seal
- Disassembling pinion bearings and matching bearings correctly for assembly
- Tightening screws of bevel ring gear
- Adjusting the bevel gear set
- Adjusting conical bearings of 4WD transfer shaft
- Adjusting conical bearings of 4WD shaft
- Rear pinion casing
- Adjusting the bevel gear set and the pump drive bearings
- Flexible coupling
- Disassembling the rear PTO
- 4WD transfer shaft
- 4WD shaft
- 4WD clutch unit
- Disassembling the 4WD clutch
- Rear PTO casing
- Rear PTO clutch
- Transmission Control Unit (GCU)
- Transmission oil filter
E0 – Rear axle
- Bleeding the braking system
- Draining the rear axle and filling with oil
- Applying sealant
- Rear differential
- Removing rear differential
- Driveline Assembly
- Tightening brake adapter screws
- Adjusting brake dead zone
- Adjusting the wheel carrier bearings
- Fitting wheel carrier cartridge seal
- Fitting brake cover seal
- EPB adjustment procedure
- Left hand rear axle
- Left hand rear ring gear
- LH brake carrier
- Left hand brake actuator
- Left hand brake discs
F0 – Front axle
- 4WD shaft
- Carrier with front axle
- Front axle
- Safety precautions
- Oil Draining Mandatory Procedure
- Pivot brackets
- Planetary reduction gearbox and steering knuckle housing
- Stub axle and steering sensor
- Steering cylinders
- Differential assembly
- Conical pinion
G0 – Bodywork – Cab – Platform
- Empty and charge the air conditioning system
- Cab
- Cab access steps
- Front cab carrier brackets
- Engine hood and front hood panels
- Lower hood guard
- Battery mount
- Front mudguards
- Mat
- Right hand console
- Left hand console
- Instrument panel
- Instrument cluster
- Right hand pillar cover
- Left hand rear pillar cover
- Seat
- Passenger seat
- Steering wheel
- Headliner trim
- Air conditioning condenser
- Dehydrator filter
- A/C unit
- Master cylinder
H0 – Hydraulic system
- Draining and filling the auxiliary utility oil
- Installing the pump dive connector sleeves
- Main oil suction line filter
- Acoustic filter
- Oil delivery line filter
- Priority valve
- Front axle suspension solenoid valve block
- Left hand hydraulic pump (22,5 + 40 + 11) cc
- Right hand hydraulic pump, 22,5 cc
- Variable displacement hydraulic pump, 85 cc
- Hydrostatic steering (orbitrol)
- Auxiliary utility oil tank
- Front lift distributors
- Disassembling the auxiliary utility distributors
- Air tanks
- Pneumatic braking system air filter
- Left hand air reservoir
- Installation of solenoid valves
L0 – Electrical system
- Battery
- Auxiliary battery
- Engine Control Unit (ECU)
- Electronic control unit (PFCU)
- Instrument panel
M0 – Front PTO
- Front PTO
- Front PTO shaft
N0 – Front lift
- Front lift arm carrier
- Front lift cylinders
- Front top link
R0 – Rear lift
- Aligning lift carriers
- Fitting lift position sensor
- Rear lift
- Rear lift hydraulic cylinders
- Rear lift arms
- Rear three-point linkage with hydraulic tie-rod
- Rear top link carrier
S0 – Wheels
- Front Wheels
- Rear wheel
V0 – Ballast – towing hitches
- Rear towing hitch
Wiring diagrams
Components
- Locations of main ECUs
- AdBlue supply module
- ISO 11786 Control unit
- Engine Control Unit (ECU)
- CTM (ECU)
- Gear Box Control Unit
- HLHP Control unit
- Service Controller Body
- TECU Service control unit
- Trailer air braking control unit – Mother regulation
- A – Starting and charging
- B – Fuses
- C – Grounds
- D – Intermediate connections
- E – On-board instruments
- F – External lights (rotating beacon)
- G – Interior lights
- H – Manual electrical controls (steering column stalk)
- I – Circuit breakers
- J – Relays
- K – Sensors and transmitters
- L – Electromagnets and solenoid valves
- M – Electrical/electronic devices, Flasher units and Timers
- N – Electric motors and actuators
- O – Resistors and rheostats
- P – Various services
- R – Diagnostics
Systems
- S001 – Power
- S002 – Starter
- S003 – Engine cooling
- S004 – Engine control system
- S005 – Emissions control system
- S006 – Front lights
- S007 – Rear work lights
- S008 – Roof lights
- S009 – Front work lights
- S010 – Sidelights and turn indicators
- S011 – Internal illumination
- S012 – Defrost and wiper
- S013 – Horn
- S014 – Mirror adjustment
- S015 – Radio
- S016 – Power socket – accessories
- S017 – Air conditioning
- S018 – Front lift
- S019 – Rear lift
- S020 – Rear mudguards
- S021 – Braking system
- S022 – Trailer brake
- S023 – Transmission
- S024 – Isobus line
- S025 – CAN “AUX” line
- S026 – “VEHICLE” CAN line
- S027 – CAN BODY line
- S028 – Agrosky
- S029 – i-Monitor
- S030 – Front axle
- S031 – Front loader
- S032 – Prewiring for solenoid valve module
- S033 – Distributors
Wiring harnesses
- 0.012.4030.4 – Front PTO
- 0.014.1567.4/30 – Front wiper motor – opening windscreen version
- 0.016.8489.4 – Trailer solenoid valve
- 0.017.0496.4/10A – H9 left hand lower front work lights
- 0.017.0496.4/10B – H9 right hand lower front work lights
- 0.017.0497.4/30A – H9 left hand bottom rear lights
- 0.017.0497.4/30B – H9 right hand bottom rear lights
- 0.017.8425.4/10 – Trailer socket, EU
- 0.017.8426.4_10 – Trailer socket (USA)
- 0.019.2379.4/20A – Front lights on left hand arm (EU)
- 0.019.2379.4/20B – Front lights on right hand arm (EU)
- 0.019.2380.4/50 – Hazard warning lights switch (USA)
- 0.019.2571.4/10 – ISO 11786
- 0.019.3659.4/30 – i-Monitor (Base version)
- 0.019.4559.4/10 – H9 rear work light (service)
- 0.019.4689.4/30A – H9 left hand rear work lights on roof
- 0.019.4689.4_30B – H9 right hand rear work lights on roof
- 0.019.4914.4_30A – LED left hand rear work lights on roof
- 0.019.4914.4_30B – LED right hand rear work lights on roof
- 0.019.5311.4/10 – Automatic A/C system
- 0.019.9829.4/30 – Agrosky SR10 antenna
- 0.020.1009.4A – Front lights on left hand arm (USA)
- 0.020.1009.4B – Front lights on right hand arm (USA)
- 0.020.8862.4/30 – Roof
- 0.020.9559.4 – Front/rear camera (10 m)
- 0.021.0490.4/10 – Trailer ABS
- 0.021.1028.4/10 – AS (Agrosky) Adapter
- 0.021.3696.4_50A – Left hand rear mudguards
- 0.021.3696.4_50B – Right hand rear mudguards
- 0.021.3866.4/30 – Front ISOBUS 11783 socket
- 0.021.5509.4 – Rear screen defrost adapter
- 0.021.2367.4/50 – Fuse box (PCB in cab)
- 0.021.8276.4 – Camera (3 m)
- 0.021.8291.4A – LED bottom front work lights
- 0.021.8291.4B – LED right hand bottom front work lights
- 0.021.8334.4A – LED left hand bottom rear lights
- 0.021.8334.4B – LED right hand bottom rear lights
- 0.023.9008.4/20 – Cowl
- 0.023.9202.4/10 – Front axle steering sensor (Dana)
- 0.023.9204.4/10 – Electrohydraulic steering (Agrosky)
- 0.023.9207.4/10 – Cable adapter on front arm
- 0.023.9248.4 – Viscostatic fan
- 0.023.9250.4_20A – Left hand rear mudguards
- 0.023.9250.4_20B – Right hand rear mudguards
- 0.023.9582.4/40 – LED front work lights on cab roof
- 0.023.9583.4/40 – H9 front work lights on cab roof
- 0.025.5687.4/10 – i-Monitor
- 0.025.5688.4 – USB video camera module
- 0.025.9765.4 – Adapter cable for i-Monitor (X25)
- 0.026.3703.4 – AdBlue quality sensor
- 0.026.6351.4 – Two-speed front power take off (PTO)
- 0.027.1782.4 – Camera 1 (3,2 m)
- 0.027.1783.4 – Camera 2 (5 m)
- 0.027.5538.4 – License plate light
- 0.027.6393.4/10 – Hydraulic trailer braking (MR)
- 0.031.4657.4A – Left turn indicator adapter cable
- 0.031.4657.4B – Left hand turn indicator adapter cable
- 0.032.8553.4 – Provision for ISO 11783 socket
- 0.033.0899.4 – AGI2 antenna cable
- 0.033.7162.4/10 – Main battery fuse box (Basic PCB version)
- 0.033.7163.4/50 – Centre wiring loom 2
- 0.033.7165.4/20 – Distributors
- 0.033.7166.4/40 – Centre wiring loom 1
- 0.033.7167.4/40 – Gearbox
- 0.033.7171.4/40 – Engine – 250 HP version
- 0.033.7172.4 – Battery power cables
- 0.033.7175.4/30 – Basic battery cables
- 0.033.7176.4 – Ethernet wiring loom
- 0.033.7177.4/10 – ABS – STOLL – EV
- 0.033.7178.4/10 – AGROSKY SR20 ELECTRIC CABLE
- 0.033.7180.4/20 – Rear ISOBUS 11783 socket
- 0.033.7181.4 – Front lift
- 0.033.7184.4 – Trailer air braking
- 0.033.7185.4/10 – Cab
- 0.033.7186.4 – Console
- 0.033.7187.4 – Works lights on roof and rear view mirrors – LED version
- 0.033.7188.4 – Auxiliary distributors
- 0.033.7189.4 – Works lights on roof and rear view mirrors – H9 version
- 0.033.7190.4/20 – Main battery fuse box (Full PCB version)
- 0.033.7191.4A – LED left hand work lights 5-6
- 0.033.7191.4B – LED right hand work lights 5-6
- 0.033.7192.4 – Hydraulic trailer braking (NO MR)
- 0.033.7259.4A – Left hand bi-LED headlights
- 0.033.7259.4B – Right hand bi-LED headlights
- 0.033.8944.4_20A – Adapter for LED left hand front TOP lights
- 0.033.8944.4_20B – Adapter for LED right hand front TOP lights
- 0.033.9905.4 – FM and DAB antenna
- 0.034.0493.4/20 – Battery – Cab adapter
- 0.034.2047.4 – FM and DAB antenna amplifier
- 0.034.2048.4 – FM antenna cable
- 0.034.2049.4 – DAB antenna cable
- 0.036.2448.4A – LED front lights on left hand arm (EU)
- 0.036.2448.4B – LED front lights on right hand arm (EU)
- 0.036.2449.4A – LED front lights on left hand arm (USA)
- 0.036.2449.4B – LED front lights on right hand arm (USA)
- 0.036.7926.4A – LED left hand turn indicator adapter cable
- 0.036.7926.4B – LED right hand turn indicator adapter cable
- 0.036.8039.4/10 – Full version battery cables + provision for front loader
- 0.036.8040.4/10 – Full version battery cables + provision for solenoid valve module
- 0.037.0255.4 – UFI filter heater interface
- 0.039.9737.4 – LED light on rear mudguard
- 0.040.1839.4 – MR_CUNA hydraulic trailer braking
- 04422324.4/10 – ISO 11786 socket
- 04436707_10A – Left hand rotating beacon
- 04436707_10B – Right hand rotating beacon
Service Info
A0 – TRACTOR
- Diagnostics 2026 subscription
- SERVICE NEWS – TTV SERIES – CRUISE CONTROL BEHAVIOUR
- After-sales 2026 subscription
- SERVICE NEWS RESEARCH GUIDE
- Diagnostics 2025 subscription
- After-sales 2025 subscription
- Diagnostics 2023 subscription
- Diagnostics 2024 subscription
- After-sales 2024 subscription
- After-sales 2023 subscription
C0 – ENGINE ACCESSORIES
- SERVICE NEWS – DEF Unit – Wrong level indication
- Possible Dust entry at air duct sleeve
- Diagnostic protocol – AdBlue – Float level unit
- Filter and prefilter tool p/n 5.9035.865.0
- SCR AREA DAMAGED SENSORS
D0 – TRANSMISSION
- SERVICE NEWS – EQ transmission – Increased noise level at specific working point
- SERVICE NEWS – EQ transmission – adjustment unit improvements
- SERVICE NEWS – T7340/7540/7560/7780 – Malfunction of HD pressure sensor
- Error 521035 – Leakage at HD pipes
- Introduction of new long filter variant at T7340/ T7540/ T7560/ T7780
- Transmission SW Update (Agrotron 6190TTV-6210TTV-6230TTV-6230HDTTV-7250TTV-7250HDTTV-8280TTV Stage 5)
F0 – FRONT AXLE
- Bevel gear set loosing screws
G0 – BODYWORK – CAB
- Brake booster pump internal damage
- Scheduled maintenance intervals
H0 – HYDRAULIC AND PNEUMATIC SYSTEM|
- SERVICE NEWS – Brake bleeding diagnostic procedure
- SERVICE NEWS – HPT – Front axle suspension – Damaged 2.8l accumulator
- Hydraulic CUNA trailer braking kit (ITALY)
- Single connection hydraulic braking kit availability update – only for EUROPEAN market
- Dry front brake discs – damaged brake pipes
- Damaged O-ring at front axle brakes charging valve block
- Oil tank-New refilling procedure
L0 – ELECTRIC AL SYSTEM
- SERVICE NEWS – New fixation for LED driving lights
- SERVICE NEWS – Software package release 2026-02
- PRESSURE SWITCH ON TRAILER BRAKE VALVE “CUNA”
- Air pressure sensor malfunction
- SerDia4.0
- iMonitor x35 malfunctioning
- GO-ANYWHERE DIAGNOSTICS
- iMonitor SW upgrade & iMonitor UBOOT update instruction
- Series 6/7/8 TTV – new software package January 2023
- Lost connection diagnostic tools
- Series 6/7/8 TTV – water in connector at external fuse box
- Water entrance in connector
- New Electrical cable P/N 0.037.0255.4/10
- PTO switch not working
- Precision Farming and iMonitor user manuals
R0 – REAR LIFT
- Twisted lifting shaft
V1 – AFTERMARKET KITS
- Check correct installation of braking KIT
- Instructions for kit aftersales
- Rear inner fenders with additional dirt protection
